Jonny Johansson

Jonny Johansson

Auto-generated profile, based on publicly available information

Jonny Johansson

Luleå University of Technology

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 October 2007 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Verified
Journal Article
Closed access
JJJonny Johansson
Jonny Johansson
PMPar-Erik Martinsson
Par-Erik Martinsson
JDJerker Delsing
Jerker Delsing
Equivalent circuits for piezoelectric devices and ultrasonic transmission media can be used to cosimulate electronics and ultrasound parts in simulators originally intended for electronics. To achieve efficient system- level optimization, it is important to simulate correct, absolute amplitude of the ultrasound signal in the system, as this determines the requirements on the electronics regarding dynamic range, circuit noise, and power consumption. This paper presents methods to achieve correct, absolute amplitude of an ultrasound signal in a simulation of a pulse-echo system using equivalent circuits. This is achieved by taking into consideration loss due to diffraction and the effect of the cable that connects the electronics and the piezoelectric transducer. The conductive loss in the transmission line that models the propagation media of the ultrasound pulse is used to model the loss due to diffraction. Results show that the simulated amplitude of the echo follows measured values well in both near and far fields, with an offset of about 10%. The use of a coaxial cable introduces inductance and capacitance that affect the amplitude of a received echo. Amplitude variations of 60% were observed when the cable length was varied between 0.07 m and 2.3 m, with simulations predicting similar variations. The high precision in the achieved results show that electronic design and system optimization can rely on system simulations alone. This will simplify the development of integrated electronics aimed at ultrasound systems.

28 June 2017 in Analog Integrated Circuits and Signal Processing
Verified
Journal Article
Open access
PDF file
JNJoakim Nilsson
Joakim Nilsson
JBJohan Borg
Johan Borg
JJJonny Johansson
Jonny Johansson
This paper analyses leakage current compensation techniques for low-power, bandgap temperature sensors. Experiments are conducted for circuits that compensate for collector-substrate, collector-base, body-drain and source-body leakage currents in a Brokaw bandgap sensor. The sensors are characterised and their failure modes are analysed at temperatures from 60 to \(230^{\,\circ }\hbox {C}\). It is found that the most appropriate compensation circuit depends on the accuracy requirements of the application and on whether a stable reference voltage is required by other parts of the circuit. Experiments show that the power consumption is dominated by leakage current at high temperatures. One type of sensor was seen to consume 260 nW at \(60 ^{\,\circ }\hbox {C}\), \(2.1\, \upmu \hbox {W}\) at \(200^{\,\circ }\hbox {C}\) and \(14\, \upmu \hbox {W}\) at \(230^{\,\circ }\hbox {C}\). This work is motivated by the need to accurately monitor the temperature of power semiconductors in order to predict emerging faults in power semiconductor modules, a task for which cheap, single-chip, low-power, high-temperature, wireless bandgap temperature sensors are appropriate.

3 April 2015 in Analog Integrated Circuits and Signal Processing
Verified
Journal Article
Closed access
PDF file
HRHans Rabén
Hans Rabén
JBJohan Borg
Johan Borg
JJJonny Johansson
Jonny Johansson

5 January 2019 in Electronics
Verified
Journal Article
Open access
PDF file
JNJoakim Nilsson
Joakim Nilsson
JBJohan Borg
Johan Borg
JJJonny Johansson
Jonny Johansson
This paper presents a circuit for realising a fuse-programmable capacitor on-chip. The trimming mechanism is implemented using integrated circuit fuses which can be blown in order to lower the resulting equivalent capacitance. However, for integrated circuits, the non-zero fuse resistance for active fuses and finite fuse resistance for blown fuses limit the Q factor of the resulting capacitor. In this work, we present a method on how to arrange the fuses in order to achieve maximal worst-case Q factor for the given circuit topology given the process parameters and requirements on capacitance. We also analyse and discuss the accuracy and limitations of the topology with regard to fuse resistance and parasitic elements such as bond pads.

1 February 2018
Verified
Conference Paper
Open access
JNJoakim Nilsson
Joakim Nilsson
JBJohan Borg
Johan Borg
JJJonny Johansson
Jonny Johansson
This paper presents electromagnetic simulations of a wireless power transfer system suitable for a monitoring system for detection of solder fatigue in power semiconductor modules. Power is provided wirelessly from a printed spiral coil on a printed circuit board to a silicon chip with an on-chip coil. We use and adapt a known gradient-ascent-based optimization algorithm to obtain suitable coil geometries. For a frequency of 433 MHz, the simulations show an efficiency of -33.9 dB which we conclude is sufficient for the proposed monitoring system.

1 September 2006
Verified
Conference Paper
Open access
GSGustav Stenberg
Gustav Stenberg
JBJohan Borg
Johan Borg
JJJonny Johansson
Jonny Johansson
GWGudmund Wannberg
Gudmund Wannberg
In order to provide instantaneous three-dimensional radar measurements spanning the entire vertical extent of the ionosphere, the planned EIS-CAT_3D incoherent scatter radar system includes multiple receive-only antenna arrays, situated at 90-280 km from the main transmit/receive site. These employs band-pass sampling at 80 MHz, with the input signal spectrum contained in the 6th Nyquist zone. This paper presents simulations and methods used to investigate use of a post-ADC fractional-sample-delay (FSD) system necessary to perform true time-delay beam-forming. To test the feasibility and limitations of the system an extensive simulation tool has been developed. The simulation system is implemented in Matlab to provide cross-platform compatibility and can be applied to any similar system. Performance degrading aspects such as noise, jitter, bandwidth and resolution can be included in the simulations. The use of FIR-filters in the base-band of a band-pass sampled signal to apply true time-delay beam-forming is shown to be feasible