Qiming Zhang

Qiming Zhang

Auto-generated profile, based on publicly available information

Qiming Zhang

Department of Mechanical & Aerospace Engineering, The Hong Kong University of Science & Technology, Clear Water Bay, Kowloon, Hong Kong

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 March 2017 in Journal of Micromechanics and Microengineering
Verified
Journal Article
Closed access
PDF file
FLFuliang Le
Fuliang Le
SLShi-Wei Ricky Lee
Shi-Wei Ricky Lee
QZQiming Zhang
Qiming Zhang
3D chip stacking with through silicon vias (TSVs) has been identified as one of the major technologies for achieving higher silicon packaging density and shorter interconnect. The test vehicle presented in this paper is a 3D chip stack package. Each layer of the test vehicle has two silicon flip chips mounted at the bottom of a silicon interposer with solder bumps. The flip chip has the equivalent dimensions and pad patterns as commercial memory chips. The interposer, with multiple interconnect TSVs for electrical connection and a central TSV for underfill dispensing, can function as a logic chip or as a redistribution chip in a real application. The assembly steps of the test vehicle include conductive adhesive filling for the interconnect TSVs, bonding two bumped flip chips on an interposer (to form a single layer), vertical stacking of the single layers and underfill dispensing. For the filling of the interconnect TSVs, an auger-dispensing method is first adopted to overfill the interconnect TSVs, followed by removing the excessive adhesive beyond the interconnect TSVs by squeegeeing. A jet valve continuously dispenses free dots of an underfill encapsulant into the central TSVs. The central TSVs function as an entrance for underfill dispensing and an uninterrupted point-source to provide fluid for each layer. The free dots form a capillary flow to fill the under-chip spaces of the test vehicle. The usage of TSVs rather than chip edges eliminates the presence of a wide edge reservoir, resulting in smaller ‘keep-out’ area occupation on the substrate.

1 May 2013
Verified
Conference Paper
Closed access
QZQiming Zhang
Qiming Zhang
CYChaoran Yang
Chaoran Yang
MTMian Tao
Mian Tao
FSFubin Song
Fubin Song
SLS. W. Ricky Lee
S. W. Ricky Lee
Hot pin pull test is frequently used for the pad crater evaluation. Although it carries several merits, it still has certain drawbacks such as time consuming and causing potential thermal impact on the PCB during the pin attachment process. In this paper, an innovative cold pin pull test method with pre-fabricated pin arrays is introduced. A set of fixture is designed and manufactured in advance. An array of pins can be attached to the test board at one time. With this fixture, instead of attaching the pin one by one, the test panel with pin arrays can be prepared after only two times of reflow without severe thermal impact. Compared with the conventional cold ball pull tests, this newly developed method cannot only equally exhibit the pad crater characteristics of the PCB, but also reduces the scattering in testing results. These conclusions are well proven by the experimental data generated in the present study.

6 October 2016
Verified
Conference Paper
Closed access
QZQiming Zhang
Qiming Zhang
JLJeffery Lo
Jeffery Lo
SLS. W. Ricky Lee
S. W. Ricky Lee
Due to the advantages of joint level tests, such as low cost and flexibility, it is always desirable to predict the board level pad cratering strength by a joint level test. In order to achieve this objective, the correlation between the joint level and the board level tests must be fully understood. Nevertheless, a precise correlation between the two types of tests for pad cratering evaluation is yet to be defined. This study investigates the correlation methodology of critical failure factors between joint and board level tests on pad cratering failure mode. An intermediate critical failure factor is taken from joint level testing as a failure criterion for failure prediction in board level testing. From the results of the experimental study and finite element analysis (FEA), the critical failure factor correlation is established between the board level and the joint level test. Subsequently the obtained failure criterion is also verified by a board level experimental study. In consequence, this indirect correlation method has the capability to predict the board level pad cratering failure with various geometric parameters.

1 May 2016
Verified
Conference Paper
Closed access
QZQiming Zhang
Qiming Zhang
JLJeffery Lo
Jeffery Lo
SLS. W. Ricky Lee
S. W. Ricky Lee
WXWei Xu
Wei Xu
WYWeihua Yang
Weihua Yang
Material characterization is a crucial part of BGA thermal warpage evaluation. In principle, the warpage behavior of BGA under temperature change is affected by the elastic modulus and the coefficient of thermal expansion (CTE) of the packaging materials. Therefore, the accuracy of material properties is critical for predicting the warpage trend and quantity. However, due to the rather thin BT substrate, it is difficult to measure the accurate orthotropic CTE in the planar direction using the conventional TMA method. This study proposes a new method to estimate the CTE of the BT substrate in PBGA devices. The required sample is cut into strips, which are bi-material beams containing the BT laminate and EMC of a PBGA. The concept of Stoney's formula is employed to establish the relations of the CTE, the curvature and other parameters of the sample. Through this method, the CTE of the BT substrate is measured using a dynamic mechanical analyzer (DMA) and calculated as a function of temperature, giving a more accurate description than the conventional temperature dependent CTE. A simulation study and the corresponding mechanism analysis are also given in this paper. With the estimated BT substrate CTE and other material properties (including elastic moduli and CTE of EMC), the warpage simulation is performed in the FEA model of the bi-material beam as a sub-model of the PBGA device to estimate the warpage behavior. From the comparison of the simulation and experiment results, the measured material properties and calculated BT CTE could lead to a reasonable prediction of warpage in both the qualitative and quantitative senses. The proposed methodology may be used for academic research and industrial applications.

18 March 2020 in Journal of Electronic Packaging
Verified
Journal Article
Closed access
PDF file
QZQiming Zhang
Qiming Zhang
SLShi-Wei Ricky Lee
Shi-Wei Ricky Lee
Repeated loading is an important reason to cause pad cratering fatigue failure in ball grid array (BGA) device in printed circuit board (PCB) assembly. For industry application, the board level drop test is commonly applied to evaluate the pad cratering fatigue strength under the repetitive drop loading. Although this testing method is consistent with the actual service condition of BGA-PCB assembly, it is extremely time consuming in the testing operation and expensive in costs. Another fatigue evaluation testing method for BGA-PCB assembly is the board level cyclic bending test. Compare with the board level drop test, this testing method can be handled by universal testing machine automatically without manual operation during the testing process. In consequence, the cyclic bending test has the merits of simple, fast, and low costs, and it is always desirable to evaluate the repeated drop life of pad cratering with cyclic bending test. This research proposes a correlation between the cyclic bending and repetitive drop test in BGA-PCB assemblies. With assistance of finite element method, the equivalent cyclic bending testing conditions of drop tests are developed. The experimental validation is also conducted to prove accuracy of the correlation. From the analysis of finite element method and experiments, both cyclic bending tests and repetitive drop tests agree with the same strain–number of cycle (S–N) curve. This means the S–N curve can be treated as a generalized failure criterion of fatigue induced pad cratering. The conclusion is crucial for reliability design phases to prevent the pad cratering fatigue failure.

10 September 2018 in Journal of Electronic Packaging
Verified
Journal Article
Closed access
PDF file
QZQiming Zhang
Qiming Zhang
JLJeffery Lo
Jeffery Lo
SLShi-Wei Ricky Lee
Shi-Wei Ricky Lee
WXWei Xu
Wei Xu
In recent years, due to the increased size of ball grid array (BGA) devices, the assembly of BGAs on printed circuit boards through surface mount technology has encountered unprecedented challenges from thermal warpage. The excessive warpage of BGAs in the reflow process may cause manufacture problems and even the risk of failure. Thus, it is essential to acquire warpage values and corresponding distribution ranges of BGAs before the surface mount technology process. In order to avoid assembly failure, theoretically, it is necessary to guarantee that all BGA devices meet the acceptance requirement of relevant standards. Generally, a large number of samples should be measured to obtain a relatively reliable warpage data distribution in the reflow temperature range, which makes this test quite costly and extremely time consuming. This study proposes another method to estimate the BGA warpage value and its possible corresponding range from the material property point of view. Because the mechanism of BGA warpage is related to the coefficient of thermal expansion (CTE) mismatch between the different materials, the warpage data scattering can be correlated with the scattering of material properties through finite element method (FEM) analysis. With a known mean value and range of material properties, the warpage value and corresponding distribution range can be solved. A sensitivity study is also presented in this paper. The accuracy of the proposed method is evaluated and the corresponding warpage data fluctuation range is estimated. From the comparison of the simulation and experiment results, determining the material properties could lead to a reasonable prediction of warpage in both the qualitative and quantitative sense. The proposed methodology for BGA warpage estimation can be used for academic research and industrial applications.