Jiangbo Zhang

Jiangbo Zhang

Auto-generated profile, based on publicly available information

Jiangbo Zhang

Michigan State Univ. (United States)

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 February 2008 in IEEE/ASME Transactions on Mechatronics
Verified
Journal Article
Closed access
WLWen Jung Li
Wen Jung Li
YLYilun Luo
Yilun Luo
NXNing Xi
Ning Xi
YWYuechao Wang
Yuechao Wang
JZJiangbo Zhang
Jiangbo Zhang
GLGuangyong Li
Guangyong Li
The main problem of atomic force microscopy (AFM)-based nanomanipulation is the lack of real-time visual feedback. Although this problem has been partially solved by virtual reality technology, the faulty display caused by random drift and modeling errors in the virtual reality interface are still limiting the efficiency of the AFM-based nanomanipulation. Random drift aroused from an uncontrolled manipulation environment generates a position error between the manipulation coordinate and the true environment. Modeling errors due to the uncertainties of the nanoenvironment often result in displaying a wrong position of the object. Since there is no feedback to check the validity of the display, the faulty display cannot be detected in real time and leads to a failed manipulation. In this paper, a real-time fault detection and correction (RFDC) method is proposed to solve these problems by using the AFM tip as an end effector as well as a force sensor during manipulation. Based on the interaction force measured from the AFM tip, the validity of the visual feedback is monitored in real time by the developed Kalman filter. Once the faulty display is detected, it can be corrected online through a quick local scan without interrupting manipulation. In this way, the visual feedback keeps consistent with the true environment changes during manipulation, which makes it possible for several operations to finish without an image scan in between. The theoretical study and the implementation of the RFDC method are elaborated. Experiments of manipulating nanomaterials including nanoparticles and nanorods have been carried out to demonstrate its effectiveness and efficiency.

31 October 2008 in IEEE Transactions on Nanotechnology
Verified
Journal Article
Closed access
JZJiangbo Zhang
Jiangbo Zhang
NXNing Xi
Ning Xi
HCHongzhi Chen
Hongzhi Chen
KLKing Wai Chiu Lai
King Wai Chiu Lai
GLGuangyong Li
Guangyong Li
Uche WejinyaUche Wejinya
Uche Wejinya
As a 1-D nanostructural material, carbon nanotube (CNT) has attracted lot of attention and has been used to build various nanoelectronic devices due to its unique electronic properties. In this paper, a reliable and efficient nanomanufacturing process was developed for building single-CNT-based nanodevices by depositing the CNTs on the substrate surface and then aligning them to bridge the electrode gap using the atomic force microscopy (AFM) based nanomanipulation. With this technology, single CNT-based IR sensors have been fabricated for investigating CNT's electronic and photonic properties. The fabrication of single-CNT-based IR sensors demonstrated the reliability and efficiency of the nanomanufacturing process. Experimental tests on single-multiwalled-CNT-based IR sensors have shown much larger photocurrent and quantum efficiency than other reported studies. It has also been shown that a high signal to dark current ratio can be accomplished by single-walled-CNT (SWNT) based IR sensors. Moreover, the testing of SWNT-bundle-based IR sensors verified that the performance of CNT bundle/film-based nanoelectronic devices was limited by the mixing of semiconducting CNTs and metallic CNTs, as well as the unstable CNT-CNT junctions in a CNT bundle or network.

28 September 2006
Verified
Conference Paper
Closed access
PDF file
JZJiangbo Zhang
Jiangbo Zhang
NXNing Xi
Ning Xi
HCHo-Yin Chan
Ho-Yin Chan
GLGuangyong Li
Guangyong Li
As a one-dimensional nanostructural material, carbon nanotube (CNT) has been used to build different nanoelectronic devices due to its unique electrical properties. In this paper, the infrared (IR) responses of individual single-wall carbon nanotube (SWNT) and SWNT film are studied. A single-wall carbon nanotube is assembled onto a pair of electrodes to form Schottky contacts. The photongenerated electron-hole pairs within the carbon nanotube are seperated by an external electric field between the two electrodes. The separated carriers contribute to the current flowing through the carbon nanotube and form photocurrent. By monitoring the photocurrent, the incident infrared can be detected and quantitated. The single-wall carbon nanotube based infrared sensor is designed and a series of efficient and reliable fabrication and assembly processes are developed for the sensor fabrication. With an atomic force microscope based nanomanipulation system as the assembly tool, a single carbon nanotube can be easily assembled onto the electrodes. Since the assembly process is controllable and reliable, it becomes possible to fabricate an individual carbon nanotubes based infrared sensor array, which was difficult to fabricate with other fabrication method. The photocurrent responses of individual SWNT IR sensor and SWNT film IR sensor are measured and analyzed. Experimental results show the good sensitivity of SWNTs to the infrared light. Our results shows a three orders higher photocurrent than the previous reported results. It has also been shown that an individual SWNT IR sensor is more sensitive than a SWNT film IR sensor.

18 January 2006
Verified
Conference Paper
Closed access
JZJiangbo Zhang
Jiangbo Zhang
GLGuangyong Li
Guangyong Li
NXNing Xi
Ning Xi
Nanomanipulation using Atomic Force Microscope (AFM) has been extensively investigated for many years. However, control of tip position during nanomanipulation is still a major issue because of the deformation of the cantilever caused by manipulation force. The softness of the conventional cantilevers also cause the failure of the manipulation of relatively large and sticky nano-object because the tip can easily slip over the nano-object. In this paper, an active atomic force microscopy probe is used to solve these problems by changing the cantilever’s flexibility or rigidity through different control strategies in imaging and manipulation modes respectively. During imaging mode, the active probe is controlled to bend up with respect to the interaction force between the tip and samples, thus making the tip response faster and increase the imaging speed. During manipulation mode, the active probe is controlled to bend down with respect to the interaction force between tip and the samples; thus increasing its nominal rigidity to avoid tip slipping over object. A detailed model of the active probe is presented in this paper and the controller designed based on the proposed active probe model is also implemented on the augmented reality system, which is an AFM based nanomanipulation system with both real-time visual and haptic feedback. The simulation results for the control strategies and the preliminary experimental results for the AFM based nanmomanipulation verified the validity of the model and effectiveness of the controller.

1 January 2007
Verified
Conference Paper
Closed access
JZJiangbo Zhang
Jiangbo Zhang
NXNing Xi
Ning Xi
HCHongzhi Chen
Hongzhi Chen
KLKing Wai Chiu Lai
King Wai Chiu Lai
Carbon nanotubes (CNTs) have a potential to be efficient infrared (IR) detection materials due to their unique electronic properties. Since carbon nanotube films lose special properties of CNTs and increase noises, a single CNT is preferred for building infrared sensors. Although some experimental progress toward individual single-walled carbon nanotube (SWNT) based IR sensor has been reported, several difficulties hindered the further development of individual CNT based IR sensors. Firstly, there is no a reliable and efficient way to reproducibly fabricate individual CNT based sensors up to now. In this paper, an automated dielectrophoresis deposition system is used to deposit CNTs around the electrodes, and then an Atomic Force Microscopy based nanomanipulation system is used to position an individual CNT onto the electrodes. Since this process is controllable and reliable, it becomes possible to fabricate an individual CNT based sensor array, which is difficult to make with other fabrication method. Secondly, since it is very difficult to control the diameter of the SWNTs during production process, it is difficult to get a SWNT based infrared sensor with expected bandgap. To solve this problem, the electronic breakdown technique is used to tune the semiconducting properties of a single multi-walled carbon nanotube (MWNT). The diameter of a single MWNT can be modified by electrical breakdown of outer layer of nanotube walls. Thirdly, SWNT has a low quantum efficiency (~ 0.02-0.1) due to its thin diameter and short absorption depth. In this paper, a single MWNT based infrared sensor is fabricated and tested. It shows a higher quantum efficiency (~ 0.3) than the SWNT based infrared sensors.

1 October 2006
Verified
Conference Paper
Closed access
JZJiangbo Zhang
Jiangbo Zhang
NXNing Xi
Ning Xi
GLGuangyong Li
Guangyong Li
CSChanmin Su
Chanmin Su
An atomic force microscope (AFM) explores the topography of a sample surface using a micro-sized flexible cantilever, which works as a flexible robot arm. The flexible cantilever is controlled to keep vibrating when an AFM works in the tapping mode. The cantilever is modeled as a flexible beam instead of a point mass system in this paper. The nonlinear interaction force between the tip and sample surface is also modeled. A simulation environment is developed to analyze the dynamics of cantilevers using the flexible beam model. Simulation results confirm that the flexible beam model can represent the system more accurately than the point-mass model. It has been shown that lower modes are more sensitive to changes of surface topography or surface materials when the cantilever is driven to vibrate at a higher harmonic mode. At the same time, this simulation environment also provides a more accurate way to validate the design of a new AFM probe and AFM controller than simulation packages which use the point-mass model