11 October 2018 in Journal of Materials Chemistry A
Despite the impressive photovoltaic performances of perovskite solar cells (PSCs) with a power conversion efficiency (PCE) beyond 22%, intensive studies are still required to overcome ongoing issues such as cost, stability, and hysteresis. Here, for the first time, we report a cesium-containing triple-cation mixed-halide perovskite solar cell (n–i–p structure) by using hydrothermally synthesized inorganic CuCrO2 (CCO) delafossite nanoparticles as a hole transporting material (HTM). After optimization of the concentration, a fully homogeneous and completely covered CCO layer that facilitates fast carrier extraction and collection was obtained on the surface of the perovskite. Our CCO-based cells achieved the best PCE of 16.7% (average 16.04 ± 0.40) with negligible hysteresis. More importantly, it was found that our cells showed a significant improvement in stability in ambient air compared with Spiro-OMeTAD HTM-based cells. After 60 days of storage in air without encapsulation, PCE remained at ∼83% of the initial value with the CCO-based cells, whereas it decreased to ∼24% of the initial value with devices based on the Spiro-OMeTAD HTM. Furthermore, cost estimation results indicated that the current prospect of CCO has an affordable cost/device ratio (∼180-fold cheaper than Spiro-OMeTAD). This work not only reveals the importance of air-stable inorganic HTMs, but also provides a low-cost HTM for highly efficient and stable PSCs.
1 January 2020 in Renewable Energy
8 November 2019 in ACS Applied Materials & Interfaces
1 October 2012 in Journal of Physics D: Applied Physics
A new and promising dye-sensitized solar cell (DSSC) bilayer design was developed using an Fe2+/Fe3+ (ferrocene) liquid electrolyte and natural dyes extracted from Hypericum perforatum, Rubia tinctorum L. and Reseda luteola. The photovoltaic parameters controlling the device performance were then investigated. A DSSC based on quercetin dye displayed the most efficient solar to electricity conversion efficiency compared with other dyes with a maximum η value of 2.17%. Maximum overall conversion efficiencies under simulated sunlight that was comparable to natural photosynthesis were increased by 15%. The identification of appropriate additives for improving V OC without causing dye degradation may result in further enhancement of cell performance, making the practical application of such systems more suitable for achieving economically viable solar energy devices.
6 July 2016 in Scientific Reports
The penternary chalcogenides Cu2CoSn(SeS)4 and Cu2ZnSn(SeS)4 were successfully synthesized by hot-injection method and employed as a catalytic materials for efficient counter electrodes in dye-synthesized solar cells (DSSCs). The structural, compositional, morphological and optical properties of these pentenary semiconductors were characterized by X-ray diffraction (XRD), Raman spectroscopy, transmission electron microscopy (TEM), energy-dispersive spectrometer (EDS) and ultraviolet-visible (UV–Vis) spectroscopy. The Cu2CoSn(SeS)4 and Cu2ZnSn(SeS)4 nanocrystals had a single crystalline, kesterite phase, adequate stoichiometric ratio, 18–25 nm particle sizes which are forming nanospheres and band gap energy of 1.18 and 1.45 eV, respectively. Furthermore, the electrochemical impedance spectroscopy and cyclic voltammograms indicated that Cu2CoSn(SeS)4 nanocrystals as counter electrodes exhibited better electrocatalytic activity for the reduction of iodine/iodide electrolyte than that of Cu2ZnSn(SeS)4 nanocrystals and conventional platinum (Pt). The photovoltaic results demonstrated that DSSC with a Cu2CoSn(SeS)4 nanocrystals-based counter electrode achieved the best efficiency of 6.47%, which is higher than the same photoanode employing a Cu2ZnSn(SeS)4 nanocrystals (3.18%) and Pt (5.41%) counter electrodes. These promising results highlight the potential application of penternary chalcogen Cu2CoSn(SeS)4 nanocrystals in low-cost, high-efficiency, Pt-free DSSCs.
1 February 2014 in Talanta
In the present work, a new caffeic acid imprinted quartz crystal microbalance (QCM) nanosensor has been designed for selective assignation of caffeic acid in plant materials. Methacrylamidoantipyrine-iron(III) [MAAP-Fe(III)] as metal-chelating monomer has been used to prepare selective molecular imprinted polymer (MIP). MIP film for detection of caffeic acid has been developed on QCM electrode and selectivity experiments and analytical performance of caffeic acid imprinted QCM nanosensor has been studied. The caffeic acid imprinted QCM nanosensor has been characterized by AFM. After the characterization studies, imprinted and non-imprinted nanosensors was connected to QCM system for studies of connection of the target molecule, selectivity and the detection of amount of target molecule in real samples. The detection limit was found to be 7.8 nM. The value of Langmuir constant (b) (4.06 × 10(6)) that was acquired using Langmuir graph demonstrated that the affinity of binding sites was strong. Also, selectivity of prepared caffeic acid imprinted nanosensor was found as being high compared to chlorogenic acid. Finally, the caffeic acid levels in plant materials was determined by the prepared QCM nanosensor.