22 December 2014 in Journal of Applied Physics
In this paper, we investigate aperiodic multilayer structures for use as narrow-angular absorbers. The layer thicknesses and materials are optimized using a genetic global optimization algorithm coupled to a transfer matrix code to maximize the angular selectivity in the absorptance at a single or multiple wavelengths. We first consider structures composed of alternating layers of tungsten and silicon or silica, and find that it is not possible to achieve angular selectivity in the absorptance with such structures. We next consider structures composed of alternating layers of silicon and silica, and show that when optimized they exhibit high angular selectivity in absorptance. In addition, as the angular selectivity in absorptance increases, the wavelength range of high angular selectivity also decreases. Optimizing the material composition of the multilayer structures, in addition to optimizing the layer thicknesses, leads to marginal improvement in angular selectivity. Finally, we show that by optimizing the absorptance of the multilayer structures at multiple wavelengths, we can obtain structures exhibiting almost perfect absorptance at normal incidence and narrow angular width in absorptance at these wavelengths. Similar to the structures optimized at a single wavelength, the wavelength range of high angularly selective absorptance is narrow.
17 March 2021 in IEEE Access
This paper describes the design, characterization, and testing of a compact hydrophone capable of measuring acoustic signals from cardiomyocytes. Our hydrophone consists of a nanofabricated photonic-crystal diaphragm externally-mounted to the facet of an optical fiber to form a pressure-sensitive Fabry-Pérot cavity. Our hydrophone can operate in small liquid volumes less than 5 mm deep and incorporates a microchannel to vent air during immersion. The venting channel is designed to optimize bandwidth and sensitivity. Modeling and experimental results in water show a bandwidth from 50 Hz to 18 kHz and a minimum detectable pressure of 3 μPa/ √{Hz}. We demonstrate the sensitivity to simulated bio-acoustic sources with nanometer-scale displacements.
1 December 2017 in AIP Advances
We introduce an optimized aperiodic multilayer structure capable of broad angle and high temperature thermal emission over the 3 μm to 5 μm atmospheric transmission band. This aperiodic multilayer structure composed of alternating layers of silicon carbide and graphite on top of a tungsten substrate exhibits near maximal emittance in a 2 μm wavelength range centered in the mid-wavelength infrared band traditionally utilized for atmospheric transmission. We optimize the layer thicknesses using a hybrid optimization algorithm coupled to a transfer matrix code to maximize the power emitted in this mid-infrared range normal to the structure’s surface. We investigate possible applications for these structures in mimicking 800–1000 K aircraft engine thermal emission signatures and in improving countermeasure effectiveness against hyperspectral imagers. We find these structures capable of matching the Planck blackbody curve in the selected infrared range with relatively sharp cutoffs on either side, leading to increased overall efficiency of the structures. Appropriately optimized multilayer structures with this design could lead to matching a variety of mid-infrared thermal emissions. For aircraft countermeasure applications, this method could yield a flare design capable of mimicking engine spectra and breaking the lock of hyperspectral imaging systems.
4 April 2022 in IEEE Sensors Journal
We develop a wavelength-multiplexed system of optical fiber-based photonic-crystal microphones for acoustic source localization. Our microphones use $392 \mu \text{m}$ wide and 450 nm thick photonic-crystal silicon diaphragms that we fabricate on the wafer scale and mount to an optical fiber with a simplified groove-based alignment. Our microphones have a bandwidth of acoustic sensitivity from 150 Hz to 50 kHz and an average minimum detectable pressure of $2 \mu Pa/ \sqrt {Hz}$ on resonance. The consistency of our microphone fabrication and assembly allows us to interrogate the pressure-sensitive Fabry-Pérot cavities using wavelength-sliced channels from the spontaneous emission of a C-band optical amplifier. Using our compact wavelength-multiplexed sensor system composed of standard fiber-optic communications hardware, we can localize acoustic sources in the environment to within 5 cm by a time-difference of arrival method.
26 July 2019 in Journal of Microelectromechanical Systems
Complex monolithic Si MEMS can be created using a single mask by extending the empty-space-in-silicon (ESS) or silicon-on-nothing (SON) technology. The fabrication combines isotropic and anisotropic etching with selective removal of passivation layers followed by hydrogen annealing. The resulting expanded design space includes multilayer structures and embedded cavities. The MEMS formation by the hydrogen annealing is simulated both at large scales and microscopic scales that together predict the shape of the finished MEMS. We demonstrate the accuracy of our process and simulations by fabricating single- and double-layer evacuated silicon voids that form Fabry-Perot optical pressure sensors with the sealed voids as pressure references. We also create multi-layered sensors with an integrated photonic crystals sensing diaphragm for improved optical readout. The sensors have a calculated 6.7 μV/Pa sensitivity and low noise over a dynamic range of over 70.9 kPa. [2019-0091]
13 June 2018 in IEEE Sensors Journal
Single-crystal silicon is an excellent optical and mechanical material, but its properties are compromised by the incorporation of other materials required for functionality or structural support. Here, we describe a monolithic silicon acoustic sensor based on a sensing diaphragm with an integrated photonic crystal (PC) mirror. Diaphragm deflection is measured in a Fabry-Perot resonator formed between the PC mirror and a gold coated single-mode fiber. The sensors are fabricated on standard silicon wafers by standard CMOS processing technologies, yielding monolithic, low-stress sensing diaphragms. The packaged sensor exhibits a minimum detectable pressure of 10 μPa/√(Hz) in the 8-17-kHz frequency range.