Vasyl Kondratets

Vasyl Kondratets

Auto-generated profile, based on publicly available information

Vasyl Kondratets

Центральноукраїнський національний технічний університет, м. Кропивницький

Research Focus & Metrics

Academic Career Length

56Years (1971-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 June 2022 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
GFGennadiy Filimonikhin
Gennadiy Filimonikhin
VYVolodymyr Yatsun
Volodymyr Yatsun
AMAnatolii Matsui
Anatolii Matsui
VKVasyl Kondratets
Vasyl Kondratets
VPVladimir Pirogov
Vladimir Pirogov
This paper has defined and investigated for stability the steady state modes of motion of a single-mass resonant vibratory machine. The vibratory machine has a platform that is supported by viscoelastic supports. The platform moves rectilinearly translationally. A vibration exciter is installed on the platform. The vibration exciter consists of N identical loads – balls, rollers, or pendulums. The center of mass of each load can move in a circle of a certain radius with a center on the longitudinal axis of the rotor. Each load, when moving relative to the body of the vibration exciter, is exposed to a viscous resistance force. It was established theoretically that with small forces of viscous resistance and any number of loads, the vibratory machine has jamming modes under which the loads that are collected form a conditional combined load and lag behind the rotor. In this case, there are two bifurcation speeds of the rotor. At speeds less than the first bifurcation speed, the vibratory machine has one single (first) jamming mode. When the first bifurcation speed is exceeded, the second and third jamming modes appear. When the second bifurcation speed is exceeded, the first and second jamming modes disappear. The first jamming mode is resonant. In the cases of two or more loads, the vibratory machine also has an auto balancing mode (no vibrations), under which the loads rotate synchronously with the body of the vibration exciter and mutually balance each other. With small forces of viscous resistance, the computational experiment found that odd jamming modes are stable if they are numbered in ascending order of the frequency of load jamming. An auto-balancing mode is stable at the rotor speeds above the resonance. For the onset of a resonant mode of motion of the vibratory machine, it is enough to slowly accelerate the rotor to a speed lower than the second bifurcation speed. The results reported here are applicable in the design of resonant single-mass vibratory machines with inertial vibration exciters of the ball, roller, or pendulum type.

26 December 2022 in National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines
Verified
Journal Article
Closed access
VKVasyl Kondratets
Vasyl Kondratets
CUCentral Ukrainian National Technical University
Central Ukrainian National Technical University
YPYuriy Parkhomenko
Yuriy Parkhomenko
MPMihailo Parkhomenko
Mihailo Parkhomenko
ABAndriy Bokiy
Andriy Bokiy
Vasyl Kondratets, Professor, Doctor in Technics (Doctor of Technic Sciences), Central Ukraіnian National Technical University, Kropyvnytskyi, Ukraine, ORCID ID: 0000-0002-1411-168Х Yuriy Parkhomenko, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Central Ukraіnian National Technical University, Kropyvnytskyi, Ukraine, e-mail: parhomenkoym@ukr.net, ORCID ID: 0000-0003-3492-3965 Mihailo Parkhomenko, director, Central Ukraіnian National Technical University, Kropyvnytskyi, Ukraine Andriy Bokiy, post-graduate, Central Ukraіnian National Technical University, Kropyvnytskyi, Ukraine Abstract The article is devoted to the theoretical substantiation of the type of beam converters in the identification of grain flow in planters. The working conditions of beam transducers in the process of sowing grain crops, types and characteristics of such transducers are considered. It is shown that the best characteristics are possessed by optocouples created on the basis of independent sources and receivers of infrared radiation in the form of silicon diodes operating in the range of 0.75...1.1 μm. This publication is aimed at the implementation of means of control during the sowing of grain crops, its topic is relevant. It is directed to the implementation of the program "Technical means of the new generation for agricultural production", included in the list of State targeted scientific and scientific and technical programs, defined by the law of Ukraine "On priority areas of development of science and technology". The publication examines the theoretical justification of the type of beam transducers in devices for identifying the grain flow formed by seeding devices of seed drills, in order to increase their resolution and quality of registration of discrete objects in the flow. As a result of the analysis of the conditions for identifying the grain flow when sowing grain crops, we come to the conclusion that it is advisable to use optocouplers from separate elements "radiation source"-"radiation receiver" of the infrared spectrum that work in the range of as beam converters. Based on the fact that the registration device includes dozens of discrete optocouplers, silicon light and photodiodes should be used as IR emitters and receivers, as they are the cheapest, simpler in circuit connection than photo transistors and sufficient to obtain the necessary resolution when registering and recognizing the flow of grains. Keywords ray converters, optocoupler, grain stream identification, infrared radiation Full Text: PDF References 1. Yevhen Solonyna. Ukraina zibrala istorychnyj maksymum zerna: scho stoit' za rekordom [Ukraine collected a historic maximum of grain: what is behind the record]. (07.10.2021). bit.ly. Retrieved from: https://bit.ly/3C90lsq [in Ukrainian]. 2. Sistema kontrolja vyseva RECORD. Tehnicheskoe opisanie i instrukcija po jekspluatacii [RECORD sowing control system. Technical description and instructions for use]. Herson. (2016). TOV «TRAK». seeding.com.ua. Retrieved from: http://seeding.com.ua [in Russian]. 3. Sistema kontrolja vyseva MONADA.. Dokumentacija, pasporta, instrukcii, programmnoe obespechenie [The MONADA sowing control system. Documentation, passports, instructions, software]. NPF «MONADA. », g. Herson, monada.ks.ua. Retrieved from: http://www.monada.ks.ua[in Russian]. 4. Rudenko. V.P. (2013). Poltavskaja tehnologіja poseva. Posobie dlja agronomov, inzhenerov s/h proizvodstva, konstruktorov [Poltava sowing technology. Manual for agronomists, engineers of agricultural production, designers]. Poltava: OOO «Kopi-Centr» [in Ukrainian]. 5. Parkhomenko, Yu.M. (2007). Doslidzhennia pidkhodiv do realizatsii prystroiu reiestratsii ta identyfikatsii zernovoho potoku [Study of approaches to the implementation of the grain flow registration and identification device]. Konstruiuvannia, vyrobnytstvo ta ekspluatatsiia sil's'kohospodars'kykh mashyn: zahal'noderzh. mizhvidomch. nauk. – tekhn. zbirnyk – Design, manufacture and operation of agricultural machiner. Issue.37. 126–131 [in Ukrainian]. 6. Kondratets', V.O. & Parkhomenko, Yu.M. (2011). Pidvyschennia dozvoliaiuchoi zdatnosti prystroiu identyfikatsii potoku nasinnia v zernovykh sivalkakh [Increasing the resolution of the seed flow identification device in grain drills]. Visnyk Kharkivs'koho natsional'noho tekhnichnoho universytetu sil's'koho hospodarstva im. Petra Vasylenka. Tekhnichni nauky. –– Bulletin of Kharkiv National Technical University of Agriculture named after Peter Vasylenko. Technical sciences, Vol.117, “Problemy enerhozabezpechennia ta enerhozberezhennia v APK Ukrainy”. 47–49 [in Ukrainian]. 7. Belokur, I.P. (1990). Defektologija i nerazrushajushhij kontrol' [Defectology and non-destructive testing]. Kyiv: Vyshha shkol [in Ukrainian]. 8. Chistjakov, S.F. & Radun, D.V. (1972). Teplotehnicheskie izmerenija i pribory [Thermotechnical measurements and devices]. Moskow: Vysshaja shkola [in Russian]. 9. Kanarchuk, V.E. Derkachev, O.B. & Chigrinec, A. D (1985). Termometricheskaja diagnostika mashin [Thermometric diagnostics of machines]. Kyiv: Vyshha shkola 10. Bastiv, V., Bendit, G. & Berveter, P. (1990). Izmerenija v promyshlennosti: Sprav. izd. v 3-h kn.; per. s nem. pod. red.. D.I. Agejkina. M.: Metallurgija, 1990. Vol. 3: Sposoby izmerenija i aparatura. 344. 11. Chistjakov, V.S. (1990). Kratkij spravochnik po teplotehnicheskim izmerenijam [Quick Reference for Thermal Measurements]. Moskow: Jenergoatomizdat [in Russian]. 12. Sivuhin, D.V. (2005). Obshhij kurs fiziki [General physics course]. Moskow: Fizizdat Vol. 836, 836 [in Russian]. 13. Shrajber, G. (2001). Infrakrasnye luchi v jelektronike [Infrared rays in electronics]. (K.O. Somova Trans.). Moskow: DMK Press [in Russian]. 14. Ermilova, N.V. (1993). Avtomaticheskaja ochistka semjan saharnoj svekly [Automatic cleaning of sugar beet seeds]. Extended abstract of candidate's thesis....

28 June 2019 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
VKVasyl Kondratets
Vasyl Kondratets
AMAnatolii Matsui
Anatolii Matsui
VYVolodymyr Yatsun
Volodymyr Yatsun
MLMihail Lichuk
Mihail Lichuk
Identification of energy efficiency of ore grinding and the liner wear by a three­phase motion of balls in a mill

9 August 2023 in Вісник Херсонського національного технічного університету
Verified
Journal Article
Open access
PDF file
ВКВ. О. Кондратець
В. О. Кондратець
АМА. М. Мацуй
А. М. Мацуй
ОСО. М. Сербул
О. М. Сербул
РТР. В. Тихий
Р. В. Тихий
Внаслідок недостатньо ефективного перемішування матеріалу в початковій частині барабана кульового млина подрібнююче середовище втрачає ефективність роботи, що приводить до перевитрати електричної енергії, куль і футерівки. Дослідженням даного процесу займався ряд авторів в Україні і за кордоном, починаючи з середини 70-х років минулого століття. Запропоновані моделі досліджень, критерій перемішування у вигляді імовірнісного коефіцієнта, який може змінюватися в межах 0…1. Однак нині задачі перемішування матеріалу в кульових млинах до кінця не вирішені. Відсутня загальна оцінка пульсацій матеріалу в барабані, не оцінено стан матеріалу на початковій ділянці і не запропоновано підходів до його покращення. Зрозуміло, що вихід з даної ситуації можливо знайти в удосконаленні кульового млина шляхом покращення його характеристик. Дослідження виконані в межах реалізації теми «Оптимізація продуктивності кульових млинів по руді і готовому продукту при мінімальних енергетичних і матеріальних перевитратах», яка входить до наукової тематики Центральноукраїнського національного технічного університету. З погляду на це тема статті є актуальною. Метою даної роботи є зменшення перевитрат електроенергії, куль і футерівки в процесі подрібнення сировини покращенням характеристик кульового млина удосконаленням завантаження руди, пісків спірального класифікатора та води на основі оцінювання пульсацій матеріалу на початковій ділянці барабана. В процесі досліджень використано метод порівняння, аналізу, методи теорії кульових млинів, теорії автоматичного керування, теорії імовірностей, математичної статистики, теорії випадкових процесів. За допомогою комп’ютерної обробки масиву даних за спеціальною програмою отримані області зміни коливальних параметрів на вході кульового млина по твердому і воді, при яких відносні відхилення маси матеріалу в агрегаті не перевищують ±3,0%, що гарантує нормальний хід технологічного процесу. Встановлено, що як по твердому, так і по воді самими небезпечними є коливання з занадто малою частотою і значними амплітудами. Важливою є проблема перемішування матеріалу в початковій частині барабана кульового млина, оскільки тут низька ефективність осереднення. Найбільш доцільним є шлях, спрямований на покращення умов перемішування ліквідацією існуючих недоліків. По-перше, перед входом руди в млин її необхідно змочити частиною потоку води, а піски перед входом в завитковий живильник максимально розрідити другою частиною потоку води. Третю частину потоку води в млин необхідно розбризкати в широкій зоні входження руди в технологічний агрегат. Такі операції забезпечують ефективне перемішування і подрібнення матеріалу вже в початковій ділянці барабана млина. Збурюючі впливи по потоку руди не порушують технологічний режим кульового млина.

1 January 2021 in National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines
Verified
Journal Article
Closed access
CUCentral Ukrainian National Technical University
Central Ukrainian National Technical University
VKVasily Kondratets
Vasily Kondratets
OSOleksandr Serbul
Oleksandr Serbul
ODOleksandr Didyk
Oleksandr Didyk
Vasily Kondratets, Professor, Doctor in Technics (Doctor of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID ID: 0000-0002-1411-168Х Oleksandr Serbul, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, e-mail: serbulan@ukr.net, ORCID ID: 0000-0003-1836-5529 Oleksandr Didyk, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID ID: 0000-0003-1454-0828 Abstract The operation of a ball mill operating in a closed loop with a spiral classifier depends on the vacuum of the pulp in it, which is characterized by a solid / liquid ratio. Supply to the entrance of the ball mill at the same time ore and sand classifier, as well as changes in the circulating load in a wide range greatly complicate the definition of this technological parameter. This situation has led to the fact that the solid / liquid ratio in mills operating in such conditions can not be automatically adjusted, in turn, the deviation of the pulp vacuum from the required value leads to significant losses. The study of the ball mill as a controlled object on the pulp vacuum channel made it possible to describe it using the mathematical expression given in the article. The solution of this expression makes it possible to characterize the change in the mass of the material in the mill over time, provided that a stepwise action is introduced at the entrance - the volume flow of water or ore. A constant value of the mass of material in the mill will clearly characterize the corresponding solid/liquid ratio. It has been found that it is important to study the filtering capabilities of the control object, as control actions on water and disturbing actions on ore can significantly change the vacuum of the pulp in some areas of the mill. The filtering capabilities of the mill can be investigated by its amplitude frequency characteristics, which showed that at low circular frequencies the amplitude frequency characteristics depend on the mode of operation of the mill - the magnitude of the circulating load and the cost of the source ore. Using computer technology, spatial diagrams of the relative oscillations of the mass of material in the mill from the amplitude and frequency of influences at its entrance through the ore and water. In the course of theoretical research it was determined that the only approach to ensure the required accuracy of determining the solid / liquid ratio in these conditions is to filter the signals before applying to the input of the identification unit of the ratio. Thus, the system of automatic control of the solid/liquid ratio at the entrance to the mill is implemented on microprocessor means. Its operation on the laboratory test bench made on the microcontroller showed high accuracy of stabilization of technological parameter, reliability in various conditions of change of characteristics of input signals. Keywords measurement of the solid/liquid ratio, optimization of the choice of measuring instruments Full Text: PDF References 1. Goncharov, Ju.G., Davidkovich, A.S., Gejzenblazen, B.E. & Gulenko, G.V. (1968). Avtomaticheskij kontrol' i regulirovanie tehnologicheskih processov na zhelezorudnyh obogatitel'nyh fabrikah [Automatic control and regulation of technological processes at iron ore processing plants]. Moskow: Nedra [in Russian]. 2. Author's certificate. 388790 USSR, MPK V03V 11/00. Ustrojstvo dlja avtomaticheskogo kontrolja zagruzki i stabilizacii razzhizhenija pul'py v mel'nice [The device for automatic control of loading and stabilization of pulp liquefaction in the mill]. No. 1420849/29-33; stated. March 30, 1970; has been published July 5, 1973, Bul. No. 29. [in Russian]. 3. Pat. 62627, Ukraine, MPK G05D7/01, V03V11/00. Sposib avtomatychnoi stabilizatsii vytrat ridyny [The method of automatic stabilization of fluid flow]. No. 2003043482; stated. April 17, 2003; has been published July 15, 2005, Bul. No. 7. [in Ukrainian]. 4. Pat. 74393, Ukraine, MPK G05D9/02, G05D7/01. Prystrij avtomatychnoi stabilizatsii vytrat ridyny [The device for automatic stabilization of fluid flow]. No. 2003043879; stated. April 25, 2003; has been published December 15, 2005, Bul. No. 12. [in Ukrainian]. 5. Pat. 59644, Ukraine, MPK V03V11/00, V02S25/00. Sposib avtomatychnoi stabilizatsii rozridzhennia pul'py v mlynakh z tsyrkuliuiuchym navantazhenniam [Method of automatic stabilization of pulp rarefaction in mills with circulating load]. No. 2002118758; stated. November 5, 2002; has been published April 15, 2005, Bul. No. 4. [in Ukrainian]. <!-- GOST Style Citations --> Citations Гончаров Ю.Г., Давидкович А.С., Гейзенблазен Б.Е., Гуленко Г.В. Автоматический контроль и регулирование технологических процессов на железорудных обогатительных фабриках. М.: Недра, 1968. 227 с. Авторское свидетельство СССР № 388790, кл. В 03 В 11/00. Устройство для автоматического контроля загрузки и стабилизации разжижения пульпы в мельнице /Дегтярёв Ф.Н., Мерзляков А.А., Кондратец В.А., Новохатько В.И., Кучма Н.И., Гуленко Т.И. - № 1420849/29-33; заяв. 30.03.1970; опубл. 5.07.1973, Бюл. № 29. Патент України № 62627, G 05 D 7/01, В 03 В 11/00. Спосіб автоматичної стабілізації витрат рідини /Кондратець В.О., Сербул О.М. - № 2003043482; заяв. 17.04.2003; опубл. 15.07.2005, Бюл. № 7. Патент України № 74393, G 05 D 9/02, G 05 D 7/01. Пристрій автоматичної стабілізації витрат рідини /Кондратець В.О., Сербул О.М. - № 2003043879; заяв. 25.04.2003; опубл. 15.12.2005, Бюл. № 12. Патент України № 59644, В 03 В 11/00, В 02 С 25/00. Спосіб автоматичної стабілізації розрідження пульпи в млинах з циркулюючим навантаженням /Кондратець В.О., Сербул О.М. - № 2002118758; заяв. 5.11.2002; опубл. 15.04.2005, Бюл. № 4. Copyright (c) 2021 Vasily Kondratets, Oleksandr Serbul, Oleksandr Didyk

2 August 2024 in Applied Questions of Mathematical Modeling
Verified
Journal Article
Closed access
ВКВ.о. Кондратець
В.о. Кондратець
ОСО.м. Сербул
О.м. Сербул
АМА.м. Мацуй
А.м. Мацуй
ОДО.к. Дідик
О.к. Дідик
Виокремлено чинники, що впливають на спрацювання молольного завантаження в каскадному режимі подрібнення руди. Серед них – ковзання, удар, перекочування по абразиву, стирання і роздавлювання абразиву, прикладена сила, прикладена швидкість переміщення. Моделювання виконано в межах розроблення теми «Оптимізація продуктивності стержневих млинів розімкнутого циклу по руді і готовому продукту за мінімальних енергетичних і матеріальних перевитрат», яка є складовою частиною наукової тематики Центральноукраїнського національного технічного університету. Тема статті актуальна. Метою роботи є розроблення критерію оцінювання спрацювання стержневого завантаження барабанного млина у вигляді математичної моделі шляхом аналізу дії впливових чинників. Застосовано методи аналізу, порівняння, математичного моделювання, теорії подрібнення руди в стержневих млинах, декомпозиції і композиції, методи теорії стійкості проти спрацювання, методи теорії спрацювання металевих тіл за взаємодії з незакріпленим абразивом. Дослідження проводилися на прикладі стержневого млина МСЦ-35-55, який нині використовують на залізорудних збагачувальних фабриках. Для нього найбільш характерним є каскадний режим роботи, за якого руда руйнується переважно роздавлюванням і стиранням. Використано оптимізоване стержневе завантаження з трьома діаметрами стержнів. У даному режимі роботи стержні найменшого діаметра відтісняються до стінки барабана, а найкрупніші зосереджуються у центральній області його поперечного перерізу. У стержневому млині молольне середовище формується укрупненими зонами зі стержнями наближено однакового діаметра, що дає змогу розглядати його як однорозмірне. Основна маса стержнів, притиснена до стінки барабана нерухомо із захопленою у нижній зоні рудою, переміщується до верхньої позначки, звідки скочується каскадом. Швидкість переміщення молольних тіл на прямій природного укосу стержнів знаходиться в межах 2,12…2,5 м/с. Установлено, що всі діючі чинники на спрацювання молольного середовища впливають на стержні різних діаметрів практично однаково. Тому можливо стверджувати, що стержні різних розмірів у діаметрі працюють практично в однакових умовах. За таких умов основним діючим чинником залишається площа контакту молольного середовища з абразивом у вигляді подрібненої руди, що рекомендовано як критерій оцінювання спрацювання стержнів. Запропоновано критерій оцінювання спрацювання стержневого молольного середовища у вигляді математичної моделі. Перспективою подальших досліджень є імітаційне моделювання спрацювання стержневого молольного завантаження в конкретних типах барабанних млинів.