Sang-Wook Ryu

Sang-Wook Ryu

Auto-generated profile, based on publicly available information

Sang-Wook Ryu

Division of Electronics and Electrical Engineering, Dongguk University, Seoul, South Korea

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 January 2024 in IEEE Transactions on Industrial Informatics
Verified
Journal Article
Closed access
ARAbd Ur Rehman
Abd Ur Rehman
SRSang-Wook Ryu
Sang-Wook Ryu
HPHyunghu Park
Hyunghu Park
JJJin-Woo Jung
Jin-Woo Jung
Fuel cell electric vehicles (FCEVs) offer a promising solution for environment-friendly and sustainable future transportation, thanks to their remarkable features (e.g., zero-carbon emission, high-power capacity, long driving range, etc.). This article extensively reviews all power electronic systems in FCEVs with special emphasis on current implementation status, recent breakthroughs, existing industrial practices, challenges, and prospects. Different from conventional studies, this article provides a more comprehensive, systematic, and organized review of all FCEV systems that can be categorized into three systems: first, fuel cell systems, including fuel cell stack and its nonisolated high-voltage (HV) dc/dc power converter; second, power backup systems, including HV battery and ultracapacitor along with their bidirectional dc/dc power converter and energy management system; and finally, driving systems, including dc/ac inverter, traction motor, regenerative braking system, and low-voltage dc/dc power converter. Finally, future challenging issues, development trends, and prospects are comprehensively discussed.

31 May 2022 in IET Renewable Power Generation
Verified
Journal Article
Open access
BBBilal Abdul Basit
Bilal Abdul Basit
ANANH TUAN NGUYEN
ANH TUAN NGUYEN
SRSang‐Wook Ryu
Sang‐Wook Ryu
HPHyunghu Park
Hyunghu Park
JJJin-Woo Jung
Jin-Woo Jung
This paper presents a state‐of‐the‐art comprehensive review of the modern control techniques for the widely recommended two distributed generation systems (DGSs) using permanent magnet synchronous generator (PMSG)‐ and doubly‐fed induction generator (DFIG)‐based wind turbines (WTs) and photovoltaic (PV) arrays in grid‐connected applications. The already published review papers individually study each DGS and also lack a systematic discussion on the control techniques without any suitable classification. This makes it difficult to study the comparatively improved performance of each control technique and comprehensively understand the control requirements of overall DGSs. Unlike existing literature, this paper first distinctively presents the generalized control configurations for both DGSs in the form of control blocks (CBs). Second, the modern control techniques suggested for each DGS are uniquely classified based on the CBs. Third, each CB is studied in detail considering its required control operation for the particular DGS component and recently proposed control techniques for its implementation. Furthermore, a detailed data analysis and comparative graphical illustrations are provided to appropriately study the merits and demerits of every state‐of‐the‐art control technique. Finally, the useful future research directions are presented to realize improved hardware components and control techniques for the grid‐connected WTs and PV arrays DGSs.

27 October 2020 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
JKJinuk Kim
Jinuk Kim
SRSang-Wook Ryu
Sang-Wook Ryu
MKMinsung Kim
Minsung Kim
JJJin-Woo Jung
Jin-Woo Jung
This paper proposes a triple-mode isolated resonant buck-boost converter over a wide input voltage range for residential applications of photovoltaic arrays and fuel cells. First, in case that the input voltage is smaller than the nominal voltage, it operates in a resonant-boost mode that boosts the input voltage by using a bridgeless structure on the secondary-side. Next, if the input voltage is within the range of the nominal voltage, it operates in a fully series-resonant mode which results in high efficiency by the soft-switching on the primary-side switches and reduced conduction loss. Last, if the input voltage is more than the nominal voltage, it operates in a pulse-width modulation (PWM) series-resonant buck mode which can achieve the step-down conversion by reducing the duty cycle. Unlike the conventional resonant converters, the proposed converter achieves high efficiency and less number of power components over a wide input voltage range. Finally, the performance of the proposed triple-mode isolated resonant converter has been fully verified on a prototype 400 W test-bed in the wide input voltage of 35-65 V.

19 May 2021 in IEEE Access
Verified
Journal Article
Open access
ANANH TUAN NGUYEN
ANH TUAN NGUYEN
SRSang-Wook Ryu
Sang-Wook Ryu
ARAbd Ur Rehman
Abd Ur Rehman
HCHan Ho Choi
Han Ho Choi
JJJin-Woo Jung
Jin-Woo Jung
This paper presents an improved continuous control set model predictive control (CCS-MPC) scheme using a fuzzy logic approach (FLA) for three-phase constant voltage constant frequency (CVCF) inverters with an output LC filter. The proposed method can enhance the output voltage quality by using an optimal predictive control law (OPCL). Additionally, the proposed method corrects the input voltage commands through the FLA-based online gain tuning aiming to satisfy the hardware constraint. Thus, the proposed FLA-based CCS-MPC can guarantee an acceptable output voltage with a faster transient response, smaller steady-state error (SSE), and lower total harmonic distortion (THD). Moreover, a Kalman filter-based load current observer is used to significantly improve the reliability and robustness. Comparative experimental studies with another CCS-MPC method are conducted on a prototype three-phase CVCF inverter using TI TMS320F28335 DSP to validate the improved performance under the step-changes of linear/unbalanced/nonlinear loads with uncertain parameters.

3 September 2021 in IEEE Access
Verified
Journal Article
Open access
SRSang-Wook Ryu
Sang-Wook Ryu
JKJinuk Kim
Jinuk Kim
ARAbd Ur Rehman
Abd Ur Rehman
HCHan Ho Choi
Han Ho Choi
JJJin-Woo Jung
Jin-Woo Jung
This paper proposes a simple 1 st -order disturbance observer (DO)-based optimal control (DOBOC) strategy for surface-mounted permanent magnet synchronous motor (SPMSM) drives. A detailed comparative analysis of three reduced-order (i.e., 1 st , 2 nd , and 3 rd ) DOs has been presented in terms of structural complexity along with transient and steady-state performances. A simple 1 st -order DOBOC is proposed with a considerably simple and easy gain tuning procedure without any complex equation and time-consuming weighting matrices selection while ensuring a competitive control performance. Also, the stability of three DOBOCs is proven using the Lyapunov function, which has not been carried out in the previous studies. Furthermore, this paper provides a detailed procedure to systematically select the controller and observer gains of three reduced-order (i.e., 1 st , 2 nd , and 3 rd ) DOBOC by experiment. Comparative experiments are performed to confirm the feasibility of the proposed 1 st -order DOBOC using a prototype SPMSM test-bed with a TI TMS320F28335 DSP. Finally, verification results and comparative table are presented to compare the speed tracking performance (e.g., transient response, undershoot (US), steady-state error (SSE), and robustness to load torque disturbances) of three reduced-order DOBOC methods under speed and load torque step-changes.

10 April 2026 in IEEE Access
Verified
Journal Article
Open access
SRSang-Wook Ryu
Sang-Wook Ryu
BBBilal Abdul Basit
Bilal Abdul Basit
ARAbd Ur Rehman
Abd Ur Rehman
HPHyunghu Park
Hyunghu Park
HCHan Ho Choi
Han Ho Choi
JJJin-Woo Jung
Jin-Woo Jung
This paper proposes a deadbeat load torque observer (DB-LTO)-based deadbeat direct torque and flux control (DB-DTFC) technique to obtain an enhanced and stable transient response of surface-mounted permanent-magnet synchronous motor (SPMSM) drives. Different from the existing DTFC approaches which control only torque and flux, the proposed DB-DTFC incorporates the speed dynamics for improving the transient control performance. Notably, a DB-LTO is proposed for fast and accurate load-torque estimation while helping to efficiently cope with the system parameter discrepancies and nonlinearities. A mathematical proof of the stability of the proposed DB-LTO-based DB-DTFC strategy is presented via eigenvalue analysis of the closed-loop system. The overall control stability is also verified by appropriately selecting the control design parameters of the proposed observer and controller gains. The proposed strategy is evaluated via extensive experimental investigations using a prototype SPMSM drive equipped with TI-TMS320F28335 digital signal processor (DSP). The improved performance is verified regarding reduction in steady-state error (SSE, from 17% to negligible), less torque ripple up to 67%, overshoot and undershoot elimination (from 25% and 16% to almost 0%), and faster transient response up to 25%, primarily resulting from the proposed DB-LTO and achieved through the enhanced DB-DTFC design under critical load-torque and motor-speed variations with inaccurate model parameters.