Vanja Asanović

Vanja Asanović

Auto-generated profile, based on publicly available information

Vanja Asanović

University of Montenegro, Podgorica, Podgorica Municipality, Montenegro

Research Focus & Metrics

Academic Career Length

27Years (2000-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2001 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
BBB. Bosnjak
B. Bosnjak
BRB. Radulovic
B. Radulovic
KPK. Pop-Tonev
K. Pop-Tonev
VAV. Asanovic
V. Asanovic

26 December 2007 in Scripta Materialia
Verified
Journal Article
Closed access
VAVanja Asanović
Vanja Asanović
KDKemal Delijić
Kemal Delijić
NJNada Jauković
Nada Jauković

28 February 2019 in International Journal of Metalcasting
Verified
Journal Article
Closed access
PDF file
JSJelena Scepanovic
Jelena Scepanovic
VAVanja Asanovic
Vanja Asanovic
SHSafija Herenda
Safija Herenda
DVDarko Vuksanovic
Darko Vuksanovic
DRDragan Radonjic
Dragan Radonjic
FKFehim Korac
Fehim Korac

1 January 2000 in ISIJ International
Verified
Journal Article
Closed access
BBBranka Bosnjak
Branka Bosnjak
BRBranko Radulovic
Branko Radulovic
KPKiro Pop-Tonev
Kiro Pop-Tonev
VAVanja Asanovic
Vanja Asanovic

1 January 2019 in Journal of the Serbian Chemical Society
Verified
Journal Article
Open access
PDF file
JSJelena Scepanovic
Jelena Scepanovic
VAVanja Asanovic
Vanja Asanovic
DRDragan Radonjic
Dragan Radonjic
DVDarko Vuksanovic
Darko Vuksanovic
SHSafija Herenda
Safija Herenda
FBFarzet Bikic
Farzet Bikic
The paper describes the mechanical properties and the corrosion behaviour of three Al?Si alloys in 0.5 M NaCl solution. The alloys have exhibited similar values of hardness, but the highest tensile strength and the lowest elongation have shown the specimens of alloy with 11.38 % of silicon. Higher content of both copper and magnesium has contributed to better tensile strength and lower elongation of as-cast hypoeutectic alloys. The harmful effects of iron on mechanical properties of all alloys have been reduced to some extent by nickel and cobalt addition. The differences in the values of the open circuit potential of the examined alloys were insignificant. The thickness of the protective oxide layer has increased over time, and the layer has become very compact. Slight differences in the values of the corrosion potential of the alloys were determined, whereas the lowest value of the corrosion current was indicated for the hypereutectic alloy. The presence of intermetallic phases in the alloys has shown that the oxide film was not consistent. The severe pits have not been found at the surface of the corroded samples. Based on the obtained results, the examined alloys may be used for the manufacturing of the internal combustion engine parts.

1 July 2006 in Materials Science Forum
Verified
Journal Article
Closed access
PDF file
KDKemal Delijić
Kemal Delijić
VAV. Asanović
V. Asanović
DRDragan Radonjić
Dragan Radonjić
This paper describes the general trends correlating mechanical and corrosion properties with chemical composition of some Al-Fe-Si and Al-Fe-Mn-Si alloys for foils. These Al-rich eutectic alloys based on Al-Fe-Si and Al-Fe-Mn, when roll cast and appropriately processed to give fine and regular dispersion of intemetallic particles, can provide good combinations of strength and ductility. These characteristics have been responsible for the alloy success in replacing commercially pure (CP) aluminum for applications in thin sheet and foil gauges. The objective was to obtain an opinion about the possible role of alloying elements in corrosion behavior and mechanical properties of these commercial materials produced by cold rolling of twin roll cast strips.