Muthusamy Kamaraj

Muthusamy Kamaraj

Auto-generated profile, based on publicly available information

Muthusamy Kamaraj

Department of Mechanical Engineering, College of Engineering and Technology, SRM Institute of Science and Technology, Chennai, India

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 December 2019 in Advanced Composite Materials
Verified
Journal Article
Closed access
MKM. Kamaraj
M. Kamaraj
EDE. Anush Dodson
E. Anush Dodson
Shubhabrata DattaShubhabrata Datta
Shubhabrata Datta
The effect of graphene as the matrix strengthener in fiber reinforced polymer composites was studied for the improvement of several properties of flax/epoxy composites. Physical and mechanical characteristics of the hybrid composite along with flammability and water absorption properties are thoroughly studied for varied quantities of graphene added to the epoxy resin. The modified epoxy resin was infused on the flax fabric using vacuum resin infusion technique. The presence of graphene in flax/epoxy composites was found to act as a flame retardant and the flammability is found to decrease with increase in graphene content. The water absorption rate was also reduced significantly to 0.1 wt% of graphene. The tensile and flexural strengths of the composites increased by 61% and 71% at 0.1 wt% of graphene but reduced for higher addition of graphene. Fractography reveals that the main mechanisms of failure were matrix fracture and interfacial debonding, predominant for higher graphene content.

2 October 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
MKM Kamaraj
M Kamaraj
RSR Santhanakrishnan
R Santhanakrishnan
EME Muthu
E Muthu
In the present work, the effect of SiC particle addition on mechanical behaviour of sisal fibre/epoxy composites was investigated. The epoxy composites were prepared by using hand layup technique. During the processing of composites, the fixed amount of sisal fibre and different amounts of SiC Particles ranging from 2 to 10 wt% were used as reinforcements. The produced composites were subjected to mechanical characterization (tensile, bending and impact tests). As per ASTM standards the test specimens were prepared to perform the mechanical testing. The findings revealed that the tensile strength and elongation at failure was reduced when the SiC particles content was increased. The increases in wt % of SiC up to 10 % drastically reduced the ultimate strength and elongation to 10.94 MPa and 0.729 % respectively, which was 39.2 % and 38.84 % lower than that of sisal fibre/epoxy composite. The flexural strength of sisal fibre/epoxy composite was increased to 74 MPa when the SiC particles increased up to 5 wt % and then reduced to 65 MPa with further increment in weight fraction of SiC particle. The impact strength was increased from 2 to 4 J/mm2 when the SiC particles content was increased up to 10 wt %. Scanning electron microscope was used to observe the fracture mechanism of the tensile test specimen. The brittle mode of failure was observed from the fractographs of the tensile test specimen.

20 September 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
MKM Kamaraj
M Kamaraj
RSR Santhanakrishnan
R Santhanakrishnan
EME Muthu
E Muthu

31 January 2022 in Journal of The Institution of Engineers (India): Series D
Verified
Journal Article
Closed access
PDF file
MKM. Kamaraj
M. Kamaraj
RMR. Manimaran
R. Manimaran
SDS. Datta
S. Datta

10 November 2022 in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
Verified
Journal Article
Closed access
SRSrinivasan Raju
Srinivasan Raju
MKMuthusamy Kamaraj
Muthusamy Kamaraj
This research aims to analyze the influence of boron carbide particles (B4C) on the mechanical and thermo-mechanical characteristics of glass fabric reinforced epoxy to identify the suitability of fabricated composites in an automotive application. The influence of B4C up to 0.4 wt% is analyzed by mixing with epoxy resin using a magnetic stirring approach, followed by compression molding with the glass fiber reinforcement. The results revealed that the hardness of glass strengthened epoxy was increased by 38%, and the other mechanical characteristics such as tensile and flexural strength were raised by 25% and 19%, respectively, when the weight fractions of B4C were raised to 0.3 wt%. From the fractography, it was observed that the fiber pull-out and fiber fracture were the dominant failure mechanisms in the developed composites during the application. The findings of the dynamic mechanical analysis revealed that the storage and loss modulus of the composites was increased by 50% and 43%, respectively, with the 0.3 wt% of B4C showing the increase in the dynamic ability of materials even at elevated temperatures.

1 June 2025 in Iranian Polymer Journal
Verified
Journal Article
Closed access
PDF file
KTKollapuri Thamilarasan
Kollapuri Thamilarasan
MKMuthusamy Kamaraj
Muthusamy Kamaraj