Recently, the study of transformer oil-based nanofluids became of great interest, due to their prospective properties as a dielectric and cooling medium. However, agglomeration of nanoparticles limits the beneficial properties that can be obtained from nanofluids. So, the work presented in this paper aims to get enhanced dispersion behavior of nanoparticles within transformer oil-based nanofluids. Then, breakdown strength with the enhanced dispersion behavior is evaluated. In order to get enhanced dispersion behavior, nanofluids were prepared using nanoparticles with a surfactant. The surfactant plays a role in the stabilization of nanoparticles and maintaining suspension stability. The considered type of nanoparticles is TiO2 nanoparticles. Two series of nanofluid samples were prepared. Through the first series, the effect of surfactant concentration on dispersion behavior and agglomerate size was studied. The dispersion of nanoparticles was characterized using three different techniques. These techniques are optical microscope analysis, transmission electron microscope (TEM) analysis and zeta potential measurements. Based on these techniques, the suitable concentration of surfactant was identified. The second series of nanofluid samples was prepared with different weight percents of nanoparticles for assessing the breakdown strength. Weibull distribution was used to calculate the breakdown probability for the base oil as well as nanofluid samples. The results showed an enhancement in the breakdown strength by about 27% in comparison to the base oil. Based on the obtained results, mechanisms behind the dispersion behavior and breakdown strength were proposed and discussed.
In this paper, a study on the dielectric properties of transformer oil-based nanofluids is presented. Titanium oxide nano ceramic particles, known as titania nanofillers, was used in the investigation process. The nanofluid samples were prepared using two-step method, in which, nanoparticles were mixed with the base oil and then dispersed using magnetic stirrer, dispersants and ultrasonic processor. Different amounts of dispersants were considered and the best amount of dispersant was determined according to the observed images obtained by an optical microscope. Different nanoparticle volume fractions were considered, starting from 0.1 g/L to 0.3 g/L. Breakdown strength was measured for the prepared samples using a liquid tester and then compared to that of the base oil. The breakdown strength increased significantly with the addition of nanofillers. The obtained results will enable to develop a new class of liquid dielectrics with a visibility for the application into power transformers.
Oil-based nanofluids have been indicated to enhance the breakdown strength and dielectric behavior of mineral oil. However, partial discharge (PD) development in these new materials has not yet been clarified. This study aims to deeply investigate PD development in nanofluids considering the role of the electrical double layer (EDL) around nanoparticles. Two types of nanoparticles (TiO2 and Al2O3) with different EDL thicknesses were used. Nanofluids were prepared using the two-step method, and their proper composition was adopted after considering their stability and avoiding the drawbacks that are present when surfactants are used. The prepared nanofluids together with the base oil were tested for PD development. First, the PD inception voltage was evaluated and analyzed using the Weibull distribution. Then, PD parameters including the PD magnitude and repetition rate were obtained for both types of nanofluids; these values were compared with the corresponding results of the base oil. Finally, the PD time transition was acquired over ten minutes of applied voltage using the segmented memory mode of the oscilloscope. Based on obtained results, physical mechanisms behind PD activity are proposed and discussed. It was found that nanoparticles with a large EDL thickness could more effectively suppress PD activity.
The development and growth in renewable technologies, practically photovoltaic (PV) arrays and wind turbines (WT) have the key role to achieve the worldwide goal towards sustainable energy systems. Hybrid renewable energy system (HRES) can provide safe, eco-friendly and economic solutions for supplying the electrical load demand. This paper developed an autonomous HRES comprising PV, WT, diesel generator, battery, and converter technologies for electrification of an agriculture-isolated area, in Sudan as a real case study. Techno-economic optimization analysis for different hybridization scenarios is performed with a main target to find the most feasible configuration with least cost and harmful emission impact considering technical, economic and environmental perspectives with aid of HOMER Pro software. The results indicate that PV/WT/diesel/battery show the most feasible solution for supplying the investigated area. The system potentially gets the minimum net present cost (NPC) and cost of energy (COE) of 17.6 M$ and 0.283 $/kWh, respectively. In addition, the proposed optimal system achieves around 93.77 % reduction in CO 2 emissions as well as 94.14% saving in fuel consumption compared to the diesel-based energy system.