Quantum technologies based on quantum point defects in crystals require control over the defect charge state. Here we tune the charge state of shallow nitrogen-vacancy and silicon-vacancy centers by locally oxidizing a hydrogenated surface with moderate optical excitation and simultaneous spectral monitoring. The loss of conductivity and change in work function due to oxidation are measured in atmosphere using conductive atomic force microscopy and Kelvin probe force microscopy (KPFM). We correlate these scanning probe measurements with optical spectroscopy of the nitrogen-vacancy and silicon-vacancy centers created via implantation 15–25 nm beneath the diamond surface and annealing. The observed charge state of the defects as a function of optical exposure demonstrates that laser oxidation provides a way to precisely tune the Fermi level over a range of at least 2.00 eV. We also observe a significantly larger oxidation rate for implanted surfaces compared to unimplanted surfaces under ambient conditions. Combined with knowledge of the electron affinity of a surface, these results suggest KPFM is a powerful, high-spatial-resolution technique to advance surface Fermi level engineering for charge stabilization of quantum defects.
20 November 2024 in Journal of Vacuum Science & Technology B
The need for reliable quantum light sources drives our research to study color centers (CCs) in silicon as telecommunication O-band emitters. Building from photoluminescence measurements, we compare new electroluminescence measurements. To this end, we synthesized CC-embedded p-i-n junctions in silicon, creating CC light-emitting diode devices. The two types of CCs synthesized were G-centers and W-centers, which show zero-phonon lines at approximately 1279 nm and 1218 nm, respectively. Here, we present our device design, fabrication process flow, and report on the device performance results from measurements to date.
The need of near-surface color centers in diamond for quantum technologies motivates the controlled doping of specific extrinsic impurities into the crystal lattice. Recent experiments have shown that this can be achieved by momentum transfer from a surface precursor via ion implantation, an approach known as “recoil implantation.” Here, we extend this technique to incorporate dielectric precursors for creating nitrogen-vacancy (NV) and silicon-vacancy (SiV) centers in diamond. Specifically, we demonstrate that gallium focused-ion-beam exposure to a thin layer of silicon nitride or silicon dioxide on the diamond surface results in the introduction of both extrinsic impurities and carbon vacancies. These defects subsequently give rise to near-surface NV and SiV centers with desirable properties after annealing.
Color centers in silicon have recently gained considerable attention as single-photon sources and as spin qubit-photon interfaces. However, one of the major bottlenecks to the application of silicon color centers is their low overall brightness due to a relatively slow emission rate and poor light extraction from silicon. Here, we increase the photon collection efficiency from an ensemble of a particular kind of color center, known as W centers, by embedding them in circular Bragg grating cavities resonant with their zero-phonon-line emission. We observe a ≈5-fold enhancement in the photon collection efficiency (the fraction of photons extracted from the sample and coupled into a single-mode fiber), corresponding to an estimated ≈11-fold enhancement in the photon extraction efficiency (the fraction of photons collected by the first lens above the sample). For these cavities, we observe lifetime reduction by a factor of . For W centers in resonant bowtie-shaped cavities, we observed a ≈3-fold enhancement in the photon collection efficiency, corresponding to a ≈6-fold enhancement in the photon extraction efficiency, and observed a lifetime reduction factor of . The bowtie cavities thus preserve photon collection efficiency and Purcell enhancement comparable to circular cavities while providing the potential for utilizing in-plane excitation methods to develop a compact on-chip light source.
The charge state of a quantum point defect in a solid state host strongly determines its optical and spin characteristics. Consequently, techniques for controlling the charge state are required to realize technologies such as quantum networking and sensing. In this work we demonstrate the use of deep-ultraviolet (DUV) radiation to dynamically neutralize nitrogen- (NV) and silicon-vacancy (SiV) centers. We first examine the conversion between the neutral and negatively charged NV states by correlating the variation of their respective spectra, indicating that more than 99% of the population of NV centers can be initialized into the neutral charge state. We then examine the time dynamics of bleaching and recharging of negatively charged SiV$^-$ centers and observe an 80% reduction in SiV$^-$ photoluminescence within a single 100-$μ$s DUV pulse. Finally we demonstrate that the bleaching of SiV$^-$ induced by the DUV is accompanied by a dramatic increase in the neutral SiV$^0$ population; SiV$^0$ remains robust to extended periods of near-infrared excitation despite being a non-equilibrium state. DUV excitation thus presents a reliable method of generating SiV$^0$, a desirable charge state for quantum network applications that is challenging to obtain by equilibrium Fermi engineering alone. Our results on two separate color centers at technologically relevant temperatures indicate a potential for above-band-gap excitation as a universal means of generating the neutral charge states of quantum point defects on demand.
Quantum technologies based on quantum point defects in crystals require control over the defect charge state. Here we tune the charge state of shallow nitrogen-vacancy and silicon-vacancy centers by locally oxidizing a hydrogenated surface with moderate optical excitation and simultaneous spectral monitoring. The loss of conductivity and change in work function due to oxidation are measured in atmosphere using conductive atomic force microscopy (C-AFM) and Kelvin probe force microscopy (KPFM). We correlate these scanning probe measurements with optical spectroscopy of the nitrogen-vacancy and silicon-vacancy centers created via implantation and annealing 15-25 nm beneath the diamond surface. The observed charge state of the defects as a function of optical exposure demonstrates that laser oxidation provides a way to precisely tune the Fermi level over a range of at least 2.00 eV. We also observe a significantly larger oxidation rate for implanted surfaces compared to unimplanted surfaces under ambient conditions. Combined with knowledge of the electron affinity of a surface, these results suggest KPFM is a powerful, high-spatial resolution technique to advance surface Fermi level engineering for charge stabilization of quantum defects.