Bilge Eryılmaz

Bilge Eryılmaz

Auto-generated profile, based on publicly available information

Bilge Eryılmaz

Gulhane Faculty of Dentistry, Department of Restorative Dental Treatment, University of Health Sciences, Etlik, Ankara, Turkey

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 September 2025 in BMC Oral Health
Verified
Journal Article
Open access
PDF file
MBMurat Büyükpolat
Murat Büyükpolat
IÇİrEm Kübra Çal
İrEm Kübra Çal
BEBilge Eryılmaz
Bilge Eryılmaz
BEBilge Ersöz
Bilge Ersöz
NANuman Aydın
Numan Aydın
SKSerpil Karaoğlanoğlu
Serpil Karaoğlanoğlu
The aim of this study was to investigate the effect of post-polymerization time and curing device type on the surface roughness, microhardness and color change of 3D printed permanent resin materials. In this study, permanent resin samples with a layer print thickness of 50 μm and dimensions of 10 × 2 mm3 were produced on SLA and DLP printers. The samples were post-polymerized in blue LED and UV LED curing devices for 10, 20, 40 and 60 min. Initial surface roughness, microhardness and color values of all polymerized samples were measured. The samples were then aged (5000 cycles) and surface roughness, microhardness and color values were measured again. Data were evaluated using two-way analysis of variance (ANOVA) and Tukey post hoc test (p < 0.05). There was no statistically significant difference in surface roughness when the samples produced in SLA and DLP printer were polymerized using blue LED and UV LED curing device for different durations (p > 0.05). The samples produced in SLA printer showed higher microhardness value when polymerized with UV LED for longer time (p < 0.05). There was no statistically significant difference in the microhardness values of DLP samples when polymerized with blue LED and UV LED (p > 0.05). When the samples produced in SLA and DLP printer were polymerized using blue LED and UV LED curing device for different durations, the color change and whiteness index increased as the post-polymerization time increased (p < 0.05). The surface roughness of the samples after aging did not change statistically significantly, while the microhardness value decreased (p < 0.05). The post-polymerization time and the type of polymerization device do not affect the surface roughness of the 3D printed samples, but increase the microhardness value. Post-polymerization time increases the color change and whiteness index values of the samples. Post-polymerization of 3D printer permanent resin materials has an effect on the mechanical and optical properties of the material. The post polymerization time of 3D resin materials and the type of curing device change the microhardness, color change and surface roughness of the material. This may affect the clinical success of the restoration.

9 December 2025 in BMC Oral Health
Verified
Journal Article
Open access
PDF file
MBMurat Büyükpolat
Murat Büyükpolat
NANuman Aydın
Numan Aydın
BEBilge Eryılmaz
Bilge Eryılmaz
SKSerpil Karaoğlanoğlu
Serpil Karaoğlanoğlu
BEBilge Ersöz
Bilge Ersöz
The use of polishing pastes in the final surface preparation of resin composite restorations has become increasingly common. This study aimed to evaluate t

7 August 2026 in BMC Oral Health
Verified
Journal Article
Open access
PDF file
FTFatma Öztürk Tunçel
Fatma Öztürk Tunçel
NANuman Aydın
Numan Aydın
SKSerpil Karaoğlanoğlu
Serpil Karaoğlanoğlu
MBMurat Büyükpolat
Murat Büyükpolat
BEBilge Eryılmaz
Bilge Eryılmaz
Recently, fluorescence-based caries detection has been integrated into intraoral scanners as a radiation-free adjunctive tool for caries assessment. Howeve