Lige Zhang

Lige Zhang

Auto-generated profile, based on publicly available information

Lige Zhang

Department of Mechanical Engineering and Mechanics, Drexel University, Philadelphia, Pennsylvania 19104, USA

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2021 in Fluid Phase Equilibria
Verified
Journal Article
Closed access
TSTejaswi Soori
Tejaswi Soori
SRSeyed Moein Rassoulinejad-Mousavi
Seyed Moein Rassoulinejad-Mousavi
LZLige Zhang
Lige Zhang
ARArif Rokoni
Arif Rokoni
YSYing Sun
Ying Sun

12 April 2021 in Physical Review Fluids
Verified
Journal Article
Closed access
PDF file
LZLige Zhang
Lige Zhang
TSTejaswi Soori
Tejaswi Soori
ARArif Rokoni
Arif Rokoni
AKAllison Kaminski
Allison Kaminski
YSYing Sun
Ying Sun
Air film stability underneath a drop is crucial for drop contact dynamics upon impact. An unstable film leads to the drop contacting the surface and subsequent spreading or splashing. Apart from previously reported film and kink contact modes, here we present the experimental evidence for a dimple failure mode of an air film, driven by a thin film instability when a drop impacts onto an atomically smooth surface. The dimple failure occurs beyond the inertial-capillary timescale and is initiated when the dimple inverts at the drop's central axis. For the same impact Weber number, the dimple failure observed in low-viscosity drops is absent at a higher viscosity, due to damping of capillary waves.

1 September 2021 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
LZLige Zhang
Lige Zhang
TSTejaswi Soori
Tejaswi Soori
ARArif Rokoni
Arif Rokoni
AKAllison Kaminski
Allison Kaminski
YSYing Sun
Ying Sun
Air film evolution underneath a drop impacting on a surface can cause the drop to either bounce off or make contact. Water drops impacting on a dry surface exhibited a transition from bouncing to the kink and film modes of contact. Additionally, a dimple mode of contact was observed on a lubricated, smooth surface. Here, we report experimental findings of drops impacting on a lubricated, smooth surface under both reduced and atmospheric pressures using liquids of two different viscosities. The kink mode observed on a dry surface only occurs at low impact velocities under reduced pressures but is completely absent at the atmospheric pressure on a lubricated surface. The horizontal extent of the dimple agrees well with the incompressible and compressible scaling within the inertial regime. The experimentally measured horizontal extent of the kink shows good agreement with the existing theoretical scaling. Slight deviations in the contact mode transition were observed between experiments and previously reported simulations, presumably due to the velocity slip at the air–lubricant interface in the present study.

18 October 2022 in Physical Review Fluids
Verified
Journal Article
Closed access
PDF file
LZLige Zhang
Lige Zhang
TSTejaswi Soori
Tejaswi Soori
ARArif Rokoni
Arif Rokoni
YSYing Sun
Ying Sun
In this paper, we use a combination of high-speed imaging and total internal reflection microscopy to study postcontact spreading dynamics and bubble entrapment of droplets impacting on surfaces lubricated with an immiscible fluid, following dimple and film modes of contact. The postcontact droplet spreading entraps two types of bubbles: (i) surface and (ii) bulk, where the former occurs when the bubbles remain at the droplet-surface interface and the latter takes place within the droplet because of the impact-induced air-cavity closure. The dimple mode of droplet-surface contact shows an absence of central surface bubble due to the contact point at the drop center and the subsequent axisymmetric spreading. The surface radial bubbles can be suppressed by tuning the impact velocity, liquid surface tension, and viscosity. Early-stage postcontact spreading dynamics are then studied for the dimple mode, where a viscocapillary scaling for the spreading radius rwet versus time t of rwet∼t is observed. Finally, the critical capillary number for wetting failure scaling is used to predict the presence of surface radial bubble entrapment with good accuracy.

8 June 2006
Verified
Conference Paper
Closed access
JYJie Yang
Jie Yang
QHQiang Huang
Qiang Huang
ZPZhaoqin Peng
Zhaoqin Peng
LZLige Zhang
Lige Zhang
SYShi You
Shi You
XZXiaojun Zhao
Xiaojun Zhao
This paper mainly discusses the construction of a human motion capture system and analyzes the captured data of human motion for humanoid motion design. Using the motion capture system, first the data of the actor motion can be obtained by setting markers on the actor's body. The data must be modified to adapt for the humanoid model because of the differences between the human and the humanoid robot. Then, the joint angels of the humanoid can be acquired by solving positive kinematics and inverse kinematics equations. The effectiveness of the proposed method is illustrated by simulations and experiments of a complicated Chinese kungfu "sword" using a 32 DOF humanoid robot.

2 October 2025 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Open access
LZLige Zhang
Lige Zhang
TSTejaswi Soori
Tejaswi Soori
MBManohar Bongarala
Manohar Bongarala
CLChanggen Li
Changgen Li
Han HuHan Hu
Han Hu
YSYing Sun
Ying Sun