1 July 2013 in International Journal of Hydrogen Energy
1 April 2015 in International Journal of Hydrogen Energy
5 November 2009 in Journal of Fuel Cell Science and Technology
The present-day high-temperature solid oxide fuel cells (SOFCs), based on yttria-stabilized zirconia (YSZ) electrolyte, a lanthanum-strontium manganite (LSM) cathode and a nickel-YSZ cermet anode, operate at . Cathode materials are restricted to doped lanthanum manganites due to their stability in oxidizing atmosphere, sufficient electrical conductivity, and thermal expansion match to the YSZ electrolyte. Reduction in the operating temperature of SOFCs is desirable to lower the costs and to overcome the technological disadvantages associated with elevated temperatures. However, as the operating temperature is reduced, the decrease in the LSM conductivity and increase in interfacial polarization resistances between the LSM cathode and YSZ electrolyte become critical. Therefore, different approaches have been proposed to improve interfacial quality and electrochemical performance of the LSM/YSZ cathode. The length of the triple-phase boundary (TPB) correlates well with the interfacial resistances to electrochemical oxidation of hydrogen at the anode and reduction in oxygen at the cathode. The extension of the TPB or the number of active reaction sites becomes, therefore, a determining factor in improving electrode performance. This can be achieved by developing electrode materials of higher ambipolar conductivity and by optimizing the microstructure of the electrodes. In order to improve SOFC performance, both composition and structure of the LSM/YSZ interface and of the cathode should be optimized. Recently, functional grade materials (FGMs) were introduced for SOFC technology. However, all studies reported in the literature so far, were focused on cathodes with only compositional gradient. On the other hand, intuitionally the best structure for a functional SOFC should be characterized by both compositional and porosity gradients. Fine grains (and high surface area) close to the electrode/electrolyte surface and large grains (and thus large pore size) at the air/oxygen side are expected to be of advantage. In the present study, “symmetrical” cathode-electrolyte-cathode SOFC single cells were fabricated. The cells consisted of the functional grade LSM cathode with YSZ/LSM cathode functional layer and LSM contact layer. The effects of various geometrical and microstructural parameters of cathode/functional layers on the overall cell performance were systematically investigated. The parameters investigated were the (1) cathode functional layer thickness and grain size and (2) the LSM contact layer thickness. Cathode performances were tested by means of electrochemical impedance spectroscopy (EIS) over a temperature range of , using air as oxidant. The dependence of cell performance on various parameters was rationalized by a comprehensive microscale model. A cathode polarization corresponding to at was achieved in this manner.
6 October 2009 in Journal of Fuel Cell Science and Technology
Electrolyte supported cells (ESC) were manufactured using tape casting and screen printing technology and the corresponding anode supported cells (ASC) manufacturing is currently under development. In the present study, “symmetrical” cathode-electrolyte-cathode solid oxide fuel cell (SOFC) single cells were also fabricated and tested using electrochemical impedance spectroscopy and scanning electron microscopy. The functional and contact layer properties were characterized by means of microscopic and electrochemical methods. Influence of thickness and grain size of layers on the cell performance was systematically investigated. the design of cell, stack and system was helped by computational fluid dynamics and system modeling. The gas flow distribution in the SOFC stack was systematically investigated. The ESC-SOFC cells developed at the Institute of Power Engineering achieved good performance as a result of improvements in ceramic processing. The present activities concentrate on ASC-SOFC cell development, cell testing and cell/stack/system design.
5 November 2013 in Journal of Fuel Cell Science and Technology
The contributions of the individual process steps of the cathode resistance were determined experimentally, directly from impedance spectra obtained from symmetrical cells. The symmetrical cells have architecture/structure consisting of YSZ electrolyte and a double layer cathode LSM-LSM/YSZ. The investigations were carried out in the temperature interval from 650 to 900 °C. The cathode processes steps activation energies obtained were 1.16 eV, 1.1 eV, and 0.09 eV (diffusion), respectively, which is in relatively good agreement with literature values. To understand the role of layer cathode thickness on electrochemical performance, electrical impedance spectra from symmetric LSM/YSZ/LSM cells were deconvoluted to obtain the key electrochemical components of electrode performance, namely ohmic resistance (RΩ), two low frequency processes related with chemical adsorption and dissociative reaction of O2 (Rp1 and Rp2), and bulk gas diffusion (W, finite warburg) through the electrode pores. The model used has Voight structure with three times constant. These parameters were then related to features, such as contact layer thickness, function layer thickness, and temperature. It was found that polarization resistance is highly dependent on the thickness of the contact layer (Rp1 and Rp2). All deconvoluted parameters are validated by using the appropriate physicochemical model.
1 October 2002 in Key Engineering Materials