2 April 2020 in National Science Review
The membrane-based reverse electrodialysis (RED) technique has a fundamental role in harvesting clean and sustainable osmotic energy existing in the salinity gradient. However, the current designs of membranes cannot cope with the high output power density and robustness. Here, we construct a sulfonated poly (ether ether ketone) (SPEEK) nanochannel membrane with numerous nanochannels for a membrane-based osmotic power generator. The parallel nanochannels with high space charges show excellent cation-selectivity, which could further be improved by adjusting the length and charge density of nanochannels. Based on numerical simulation, the system with space charge shows better conductivity and selectivity than those of a surface-charged nanochannel. The output power density of our proposed membrane-based device reaches up to 5.8 W/m2 by mixing artificial seawater and river water. Additionally, the SPEEK membranes exhibit good mechanical properties, endowing the possibility of creating a high-endurance scale-up membrane-based generator system. We believe that this work provides useful insights into material design and fluid transport for the power generator in osmotic energy conversion.
1 July 2021 in Journal of Hazardous Materials
1 November 2013 in Polymer Chemistry
A new difluoride monomer containing electron-rich tetraphenylmethane was designed and synthesized. Based on this monomer along with 4,4′-(hexafluoroisopropylidene)diphenol (6FBPA) and 4,4′-difluorobenzophenone (DFB), a series of tetra-sulfonated poly(aryl ether ketone)s (TS-PAEK-x) were prepared by nucleophilic polycondensation, followed by a sulfonation reaction using chlorosulfonic acid. Tough, flexible, and transparent membranes were obtained by solvent casing. These membranes with ion exchange capacity (IEC) values ranging from 0.85 to 1.43 meq. g−1 exhibited good mechanical properties, excellent dimensional stability, and suitable proton conductivity. The largest swelling ratio (in-plane direction) with a value of 10.3% was observed from TS-PAEK-25 (IEC = 1.43 meq. g−1) membranes at 100 °C, which was much lower than that of Nafion 117 under the same conditions. The highest proton conductivity of 151 mS cm−1 was obtained from the TS-PAEK-25 membrane at 100 °C in the fully hydrated state. Compared to Nafion 117, TS-PAEK-25 with comparable water content exhibited a superior effective proton mobility (μ) value (up to 1.19 × 10−3 cm2 s−1 V−1). Under reduced humidity conditions, TS-PAEK-25 showed desired conductivity considering its lower IEC level. The results indicate that the TS-PAEK-x membranes are promising candidates for application as proton exchange membranes.
12 May 2021 in ACS Applied Materials & Interfaces
1 May 2013 in Journal of Membrane Science
12 November 2012 in Journal of Materials Chemistry A
The preparation and characterization of new polymeric ionomers based on a fully aromatic poly(arylene ether) backbone with locally pentasulfonated pendent groups for applications as proton exchange membranes is reported. The high molecular weight sulfonated polymers were obtained by the polycondensation of new (2,6-difluorophenyl) (4-(1,2,3,4,5-pentaphenylbenzene)phenyl)methanone, 4,4′-difluorodiphenyl methanone, and 4,4′-dihydroxydiphenylsulfone, followed by sulfonation using sulfuric acid in high yields. The polymers produced tough, flexible, and transparent membranes by solvent casting. Membranes with ion exchange capacities between 0.8 and 1.7 mEq g-1 showed high proton conductivities and low methanol permeabilities. Compared to Nafion 117, these sulfonated membranes exhibited better microphase separation morphologies. The fully humidified membranes also exhibited considerably good mechanical properties, with tensile strengths from 35 to 45 MPa and elongations at break from 23 to 49%. This investigation demonstrates a controllable high density sulfonated side group of a poly(arylene ether sulfone) membrane with tunable and balanced properties, which is promising for proton exchange membrane fuel cell technology.