18 March 2025 in IEEE Transactions on Energy Conversion
High-silicon steel 10JNEX900 is often considered as a good core material for high-speed motors due to its low losses. However, cores are often operated under the multi-physics coupling (rotating and harmonic magnetic field, temperature, mechanical stress) resulting in variations in iron loss, which directly affects the modeling accuracy of the motor. In order to accurately predict the 10JNEX900 motor loss, this paper conducts iron loss tests under multi-physics coupling on two kinds of silicon steel materials, high silicon steel 10JNEX900 (6.5% Si) and conventional silicon steel ST100 (3.0% Si), and analyzed the differential change rule of 10JNEX900 loss. On this basis, the article proposes a model for calculating the iron loss of 10JNEX900 motor considering multi-physics coupling factors, and calculates the iron loss of silicon steel sheet. Meanwhile, the magnetic field, temperature field and stress field of the permanent magnet synchronous motor were calculated by the finite element method. The differences in motor performance before and after considering the multi-physics field factors are also compared. Finally, the motor prototype is fabricated and tested. The difference between the predicted and measured iron loss in the motor at no-load is lower than 10%.
1 February 2023 in AIP Advances
Electrical steel cores in electric motors are often operated under variable temperature conditions, and the temperature has a large impact on the magnetic properties of electrical steel. Different Silicon content also makes electrical steel have different performance characteristics. Therefore, in this paper, an environmentally adjustable electrical steel magnetic property testing system is built to investigate the magnetic property variation of non-oriented electrical steel sheets with different Si contents at different temperatures. Through the experiments in this paper, it is found that the trend of magnetic properties of electrical steels tends to flatten out with increasing Si content under the influence of temperature. In particular, the loss of 6.5% Si shows a trend of first decreasing and then increasing with the increase of temperature. The internal grain structure of electrical steel can explain this phenomenon very well. The larger the grain size, the less the magnetic properties of electrical steel are affected by temperature. In order to further analyze the variation phenomenon of electrical steel loss, the loss separation calculation was carried out for 5 more electrical steels with different Si content in this paper. The reason for this phenomenon was finally explained by a special preparation process of 6.5% Si.
15 May 2024 in IEEE Transactions on Magnetics
The deteriorating effect of the cutting process on the magnetic properties of electrical steel is well recognized. However, more studies have focused on the effect of different cutting techniques on a single electrical steel material. Electrical steel also exhibits different magnetic properties depending on its Si content. Therefore, more research is needed to gain insight into the interactions between two commonly used processes, wire electrical discharge machining (WEDM) and laser cutting, and electrical steels with different Si contents. In this article, the effects of WEDM and laser cutting on the magnetic properties of three kinds of non-oriented electrical steels with different Si contents are investigated. At the same time, the trend of the deterioration of the magnetic properties of 6.5% Si with different cutting area shares under the two cutting methods is explored. Finally, this article explains in detail the reasons why the magnetic properties of electrical steel are differently affected by the cutting methods from the grain point of view and separates and analyzes the electrical steel losses affected by cutting.
3 June 2024 in IEEE Transactions on Magnetics
Non-oriented electrical steels used as motor cores are subjected to mechanical stress, which has a significant impact on their magnetostrictive properties. Moreover, electrical steels with different Si contents will also show different magnetostrictive properties. Therefore, in this article, the magnetostrictive properties of four kinds of non-oriented electrical steel sheets with different Si contents were tested under tensile stress. Experiments show that the magnetostrictive strain of electrical steel decreases with increasing Si content. Meanwhile, under the influence of tensile stress, the magnetostrictive effect of electrical steel begins to decrease, and the trend of this change shows an increasing and then decreasing trend with the increase of Si content. It is noteworthy that the magnetostrictive strain of 6.5% Si is minimally affected by both the tensile stress and the magnetic flux density. Finally, this article explains the variation rule of magnetostrictive effect of electrical steel with different Si contents under the influence of tensile stress in terms of the micro-magnetic mechanism of the magnetostrictive effect and micro-grain structure of electrical steel.
1 April 2023 in AIP Advances
With the development of electric motors, high speed and high efficiency have become the new development trend. Therefore, reducing the iron loss of motors has become the focus of academia and industry. Amorphous alloys are gradually being used in high speed motors by virtue of their low loss characteristics at high frequencies. Amorphous alloys generate large internal stresses during the manufacturing process, and annealing is usually required to eliminate the effect of internal stresses on magnetism. Amorphous transformer cores are usually annealed by applying a magnetic field in the direction of the magnetic circuit to improve the magnetic domain state, increase the saturation density in that direction, and reduce iron loss. Since the magnetic field of the motor stator teeth is pulsating, and amorphous annealed under longitudinal magnetic field (AALM) has the most performance along the direction of the annealed magnetic field. Therefore, in this paper, the magnetic properties of AALM, annealed amorphous (AA), and unannealed amorphous (UA) are tested to prove the advantages of the material, and then AALM is spliced as the tooth of the motor. The advantages of this material in the motor species are further demonstrated by designing a comparative simulation scheme in the longitudinal direction (same material with different structure) and in the transverse direction (same structure with different material).