1 January 2016 in Procedia Engineering
Activated carbon was produced from palm kernel shell (PKS) and coconut shell (CS) through physical steam activation and chemical activation. The optimum activation temperature for physical activation is 800oC and for chemical activation is 550oC. The activated carbons produced also loaded with different metal oxides (BaO, MgO, CuO, TiO2 and CeO2). Both loaded and unloaded activated carbons are characterized using ultimate analysis, BET surface area measurement method, fourier transform infrared (FT-IR) analysis and x-ray diffraction (XRD) analysis. The BET surface area and pore volumes showed that the activated carbons prepared from PKS by chemical activation (PCAC) and from CS by physical activation (CPAC) were found to be much higher than others activated carbons. Hence, the metal oxides were loaded on these two activated carbons. The loaded and unloaded activated carbons produced will be tested for application of CO2 adsorption from the simulated flue gas
1 January 2013 in Procedia Engineering
Activated carbon has been known as an excellent adsorbent and is widely used due to its unique characteristics and large adsorption capacity. In this study, activated carbon produced from oil palm empty fruit bunch by steam activation was used. The activated carbons were analyzed using nitrogen adsorption isotherm as BET for specific surface area and Fourier transform infrared (FT-IR) spectroscopy. The results showed that the activated carbon at these optimum conditions; 765°C activation temperature and 77 min activation time, possesses a large apparent surface area (SBET = 720 m2/g), total pore volume (0.341cm3/g) with average pore size diameter of 18.99 Å. FT-IR results indicate that all the oil palm empty fruit bunch was successfully converted to carbon
1 December 2013 in Key Engineering Materials
SKSharifah Aishah Syed A. Kadir
Sharifah Aishah Syed A. Kadir
This paper explains preparation of activated carbon from empty fruit bunch (EFB) using steam activation under optimum conditions; activation temperature of 765°C and activation time of 77min and analyzes their physical and chemical properties using proximate and ultimate analysis, fourier transform infrared (FT-IR) analysis, x-ray diffraction (XRD) analysis, nitrogen adsorption-desorption analysis and scanning electron microscopy (SEM) analysis. Results show activated carbon EFB consists of 68.32 wt% carbon, 3.12 wt% hydrogen, 2.12 wt% nitrogen and 26.44 wt% oxygen content. FT-IR spectroscopy result indicate that raw EFB was successfully converted to carbon after activation process and was proven by spectra of commercial activated carbon. The XRD study confirms the presence of some crystalline (graphite) phase around peaks 26o and 43o. Characterization by using BET and SEM analysis showed that activated carbon produced from EFB has good properties with high surface area (720.0 m2/g) and well developed pores.
30 March 2023 in Bioinorganic Chemistry and Applications
An effective recovery technology will be valuable in the future because the concentration of the precious metal contained in the source can be a key driver in recycling technology. This study aims to use response surface methodology (RSM) through Minitab software to discover the optimum oxygen level (mgL−1), e-waste pulp density ( w/v), and glycine concentration (mgL−1) for the maximum recovery of gold (Au) and silver (Ag). The method of precious metals recovery used for this study was taken from the bioleaching using 2L of batch stirred tank reactor (BSTR). A Box-Behnken of RSM experimental statistical designs was used to optimize the experimental procedure. The result of the RSM optimization showed that the highest recovery was achieved at an oxygen concentration of 0.56mgL−1, a pulp density of 1.95, and a glycine concentration of 2.49mgL−1, which resulted in the recovery of 62.40 of Au. The pulp density and glycine concentration greatly impact how much Au is bioleached by C. violaceum. As a result, not all of the variables analyzed seem crucial for getting the best precious metals recovery, and some adjustments may be useful in the future.
1 August 2021 in IOP Conference Series: Materials Science and Engineering
Coal bottom ash (CBA) is the solid residue produced from coal-fired power plant. It is classified as hazardous material, which can cause adverse effect to the environment and public health. In view of the situation, exploring and discovering possible utilization of these coal residues into value-added products has to be performed. Hence, the aim of this paper is to investigate the potential of raw CBA as an adsorbent for carbon dioxide (CO2) gas adsorption. The physicochemical characteristics of CBA were determined using ultimate and proximate analysis, nitrogen adsorption-desorption isotherm, scanning electron microscopy (SEM), and elemental diffraction x-ray (EDX) analysis. CO2 adsorption study was conducted using simulated flue gas by pressure swing adsorption process in a fixed-bed reactor to evaluate the suitability of CBA as an adsorbent material. High carbon content in CBA makes it’s become a good precursor for production of carbonaceous adsorbent. Trace elements like calcium, silica and alumina, indicating that the material had a good adsorption capacity. The result indicated that CBA was able to adsorb CO2 with the adsorption capacity of 0.000276 mol CO2/g CBA. As a conclusion, CBA has the potential to be an adsorbent for its application in gas phase especially in CO2 adsorption.