27 July 2020 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
For oil and gas seismic exploration, rock velocities are essential parameters to tease out reservoir properties from seismic data. The ultrasonic pulse transmission (UPT) method has been a gold standard to estimate reservoir rock velocities in the laboratory. As regards the UPT method, accurate determination of traveltime of waves plays a significant role in robustly measuring rock velocities. One of the most conventional ways to obtain the traveltime is through the arrival picking. However, unclear noise virtually exists preceding the arrival of S-wave interfering this arrival picking, which sometimes can cause enormous errors to measured S-wave velocity. Herein, we develop a two-dimensional, three-component (2D-3C) finite-element modeling (FEM) algorithm aiming to interpret the noise by combining with UPT measurements. The proposed 2D-3C FEM not only can efficiently compute ultrasonic wavefield radiated by circular P- or S-wave transducers, but also able to obtain synthetic waveforms in the testing of S-wave velocity where polarization directions of S-wave transducers are arranged as non-parallel. To analyze simulated ultrasonic waveforms, we introduce frequently-used concepts of edge and direct plane waves to build elastodynamic models of ultrasonic wavefield. Then, we compare numerical results with experimental measurements. Our 2D-3C FEM results show good agreement with experimental waveforms both in P- and S-wave velocity testings. Whereafter, we pinpoint constitutions of the noise preceding the arrival of S-wave. Comparison of numerical and experimental waveforms suggests that the edge P-wave with its reflected and converted modes partially contribute to this noise, while the rest part of the noise may stem from the effects of the compressional dipole, the couplant smeared between a transducer and a sample, and inherently parasitic longitudinal vibrations of S-wave transducers. The interpretations on this noise have the potential to benefit future design of more effective S-wave transducers.
27 July 2023 in Geophysical Journal International
SUMMARY: Modelling the dispersion and attenuation of seismic waves in partially saturated rocks is important for quantitative interpretation of seismic data. To observe the partial saturation effects on modulus and attenuation, three sandstone samples with different porosities were used in the laboratory experiment. The samples were measured by ultrasonic testing system under different water saturation using drainage process. The experimental results show that the bulk modulus more rapidly increased at higher saturations (>80 per cent), and attenuation peaks could be observed. Then we develop a new partial saturation model based on Chapman’s theory and poroelastic theory. The new model is consistent with the Gassmann equation when the water saturation is 0 or 100 per cent. By analysing the characteristic frequency, the new model can be concluded in the form of a standard linear solid model. A comparison of the new model with the White model and the measured data is conducted. The results show that the model performed well at predicting the effective bulk modulus and attenuation of the rock with different water saturation. Finally, we discussed the impact of frequency, fluids and pore structures on the new model. The results reveal that the new model will be helpful in discussing partial saturation in rocks.
28 September 2023 in Geophysics
The modeling of seismic wave velocity and attenuation is crucial for the interpretation of seismic data. In fluid-saturated rocks, the presence of fractures causes dispersion and attenuation of seismic waves due to fluid flow between cracks and pores. Meanwhile, the parallel distribution of cracks is an important reason for the anisotropy of rocks. Combined with poroelasticity theory, we extend Chapman’s model to media with penny-shaped fractures and an isotropic porous matrix, for which no restrictions are placed on the pore shape of the matrix. We conduct simulations at different frequencies to indicate the predicted anisotropy of velocity and attenuation. The variation of velocities and attenuations with orientation angle is consistent with Chapman’s model. Because a typical porous matrix is used in the new model, predicted velocities are lower than those under assumption of spherical matrix pores. Then, we analyze the effect of pore compressibility of the matrix on the velocity and attenuation. We also conduct discussions about the effect of different porosities on velocity and attenuation. The analysis indicates that the predictions of the new model are more closely related to the modulus of the porous matrix than Chapman’s model. The strength of fluid flow in the new model also will change with the matrix pores. The comparison of the new model and Chapman’s model with experimental data indicates that the new model is in better agreement with the experimental results.