12 August 2014 in Optics Express
Optics InfoBase is the Optical Society's online library for flagship journals, partnered and copublished journals, and recent proceedings from OSA conferences.
1 August 2013 in AIP Advances
A prospective move to 10.5 and 11.2 nm wavelengths, as an alternative to 6.7 and 13.5 nm, for next generation nanolithography is discussed. Ten-mirror optical systems based on Ru/Be, Mo/Be, Rh/Sr, Mo/Si, and La/B multilayers were compared for efficiency at their working wavelengths. It is shown that a transition to 10.5 nm and 11.2 nm may be a solution to the problem of increasing performance and resolution of a projection system.
7 January 2013 in Applied Physics Letters
Results on optimization and manufacturing of La/B4C multilayers are reported. Such mirrors are promising optical elements for the development of the next generation of nano-lithography at an operation wavelength of 6.7 nm. A near-normal incidence reflectivity of up to 58.6% has been measured at the BESSY-II soft x-ray reflectometer beamline. This is the highest reflectivity measured so far at this wavelength. The potential to further increase the reflectivity of the multilayers is discussed.
15 October 2001 in Applied Physics Letters
Periodic magnetic nanodot arrays have been produced on an area as large as by direct nanolithography using interferometric laser radiation. The dots are formed by the local annealing of sputtered amorphous Co–C films in regions where the laser intensity is highest. At room temperature the dots exhibit ferromagnetic order and are embedded in a paramagnetic matrix. The onset of room-temperature ferromagnetism is caused by nanoscale chemical and morphological changes during dot formation and reflects the phase separation of magnetic Co-rich clusters. The present single-step nanolithography is potentially an efficient method for fabrication of patterned magnetic arrays.
14 March 2016 in Applied Optics
We provide an analysis of contemporary multilayer optics for extreme ultraviolet (EUV) solar astronomy in the wavelength ranges: , , , and . We found new material pairs, which will make new spaceborne experiments possible due to the high reflection efficiencies, spectral resolution, and long-term stabilities of the proposed multilayer coatings. In the spectral range , Mo/Be multilayer mirrors were shown to demonstrate a better ratio of reflection efficiency and spectral resolution compared with the commonly used Mo/Si. In the spectral range , a new multilayer structure Al/Si was proposed, which had higher spectral resolution along with comparable reflection efficiency compared with the commonly used Al/Zr multilayer structures. In the spectral range , the multilayer structure turned out to best obey reflection efficiency and long-term stability. The and Cr layers prevented mutual diffusion of the Si and Mg layers. For the spectral range , a new multilayer Mo/Mg-based structure was developed; its reflection efficiency and long-term stability have been analyzed. We also investigated intrinsic stresses inherent for most of the multilayer structures and proposed possibilities for stress elimination.
16 February 2016 in Applied Optics
We have studied the surface treatment of polished fused silica by neutralized Ar ions with energy of 500–1500 eV and incidence angles of 0–90°. We found the following regularities: for samples that passed the standard procedure of deep polishing (initial effective roughness ), the effective roughness decreases to the ultrasmooth level (i.e., in the range of spatial frequencies ). The effect begins to be noticeable at the material removal of 150 nm and reaches saturation at depths of removal greater than 1 μm. For supersmooth samples (), the effective roughness keeps the initial level at material removal down to tens of micrometers. The optimal ion energy range is 800–1300 eV (maximum smoothing effect); at higher energy some surface roughness degradation is observed. All the smoothing effects are observed at the incidence angle range . Increasing the ion energy above 1300 eV increases the etching rate by up to 4 μm per hour (), which allows for deep aspherization of sized substrates. The technique allows for manufacturing the optical elements for extreme ultraviolet and soft x-ray wavelength ranges with a numerical aperture of up to 0.6.