Lithium-ion batteries, simply known as lithium batteries, are distinct among high energy density charge-storage devices. The power delivery of batteries depends upon the electrochemical performances and the stability of the electrode, electrolytes and their interface. Interfacial phenomena of the electrode/electrolyte involve lithium dendrite formation, electrolyte degradation and gas evolution, and a semi-solid protective layer formation at the electrode–electrolyte interface, also known as the solid–electrolyte interface (SEI). The SEI protects electrodes from further exfoliation or corrosion and suppresses lithium dendrite formation, which are crucial needs for enhancing the cell performance. This review covers the compositional, structural and morphological aspects of SEI, both artificially and naturally formed, and metallic dendrites using in situ/in operando cells and various in situ analytical tools. Critical challenges and the historical legacy in the development of in situ/in operando electrochemical cells with some reports on state-of-the-art progress are particularly highlighted. The present compilation pinpoints the emerging research opportunities in advancing this field and concludes on the future directions and strategies for in situ/in operando analysis.
30 March 2017 in The Journal of Physical Chemistry C
Tin mono-sulfide (SnS) nanorods (NRs) have been successfully synthesized through a solvothermal process using hydrated tin(II) chloride and sodium sulfide as precursors and N,N-dimethyl formamide (DMF) as solvent. The Reitveld refined powder X-ray diffraction (PXRD), Raman and 119Sn solid-state NMR experiments have confirmed the presence of a SnS phase with Pnma space group and a SnS2 phase with Pm1 space group as a minor impurity. HRTEM and HRSEM studies have confirmed the nanoparticle shape as nanorods (NRs). The growth of the NRs has been explained from the observation that by increasing the solvothermal temperature, nanorods grow preferentially in the [100] direction. Optical properties of the SnS nanorods were measured and it was found that all NRs have an indirect band gap in the range of 1.10 eV to 1.2 eV. The electrochemical properties for lithium storage (half-cell configuration) have been tested against Li/Li+ using conventional polyvinylidene fluoride (PVDF) binder and an eco-friendly, low cost binder, carboxy methyl cellulose (CMC). After fifty cycles of charge–discharge, the CMC binder electrode shows a superior electrochemical charge storage property of 591 mA h g−1 compared with 385 mA h g−1 for the PVDF binder electrode, at 160 mA g−1 current rate. At a high current rate of 350 mA g−1, the SnS NRs with the CMC binder shows a discharge capacity of 565 mA h g−1 after 50 cycles, therefore exhibiting excellent properties for a lithium battery anode as it can maintain a high capacity and coulombic efficiency continuously for 50 cycles.
25 October 2016 in ACS Sustainable Chemistry & Engineering
The electrochemical performance of tin sulfide (SnS) nanorods (NRs) as an anode for lithium-ion batteries has been evaluated, after adding a carbon coating and reduced graphene oxide (r-GO) as a conductive support. Raman spectroscopic analysis of such types of carbon-coated SnS nanorod clearly shows the influence of the size and shape of the conductive graphite crystallites on their electrochemical performance against Li/Li+. The incorporation of an r-GO support for the SnS nanorods enhances the electrochemical performance. The SnS NRs/r-GO composite with both reduced graphene oxide and a carboxymethyl cellulose binder shows better performance than the carbon-coated sample. The ex situ transmission electron microscopy studies show that the carbon coating of the SnS nanorod is ruptured during the lithiation process and the particle size is not maintained uniformly, while the r-GO composite is able to maintain its shape and size during the continuous charge–discharge process. The discharge capacity of the SnS NRs/r-GO composite was 602 mA h g−1 at a current rate of 160 mA h g−1 after fifty continuous charge–discharge cycles. The current observations suggest that the practical energy density need not be sacrificed for power density, provided that the carbon coatings are optimized by the careful selection of additives.