26 August 2020 in IEEE Transactions on Geoscience and Remote Sensing
The purpose of seismic reservoir characterization is to predict the spatial distribution of the subsurface rock properties from a set of direct and indirect measurements. Commonly, rock property volumes are obtained in a two-steps approach. First, the elastic properties are inverted from seismic reflection data and then used to compute rock properties volumes by applying a calibrated rock physics models. Such an approach is not only time consuming but may also lead to biased results as the uncertainties related to seismic inversion may not be propagated through the entire geomodeling workflow. Here, we propose an iterative geostatistical shale rock physics seismic AVA inversion method to invert seismic reflection data directly for shale rock properties. The workflow consists of three main steps starting from shale properties model generation of brittleness, total organic carbon (TOC), and porosity using stochastic sequential simulation and cosimulation and calculation of a volume of shale. In the following step, elastic property volumes are calculated based on a calibrated shale rock physics model using the self-consistent approximation. The elastic models are then used for the calculation of the synthetic seismic data. In the final step, the misfit between synthetic and real data is calculated and used as part of the stochastic update of the model parameter space. The whole process is repeated until a minimum misfit between the observed and synthetic seismic is achieved. The proposed method is successfully tested on an onshore Lower Paleozoic shale gas reservoir in Northern Poland, and the predicted shale rock properties agree with those observed at a blind-well location.
1 August 2018 in Interpretation
We have developed a case study of amplitude variation with azimuth (AVAZ) analysis applied to quantify the amount of the azimuthal anisotropy present in the Lower Paleozoic shales of the Baltic Basin (northern Poland). The challenges encountered here are related to thin (up to 25 m) deeply buried (approximately 3 km) targets, characterized by a weak average azimuthal anisotropy (1%–2% from cross-dipole sonic data). Synthetic AVAZ modeling confirms the applicability of the method. We used data after full-azimuth angle-domain prestack depth migration (PSDM) processed by a contractor and in-house sectored prestack time migration (PSTM). Application of AVAZ on full-azimuth PSDM data provided results that were further corroborated by the available calibration data. Anisotropy azimuths from AVAZ correlate with natural fracture direction from image logs (x-tended range microimager [XRMI]) interpretation, especially at the wells with only one dominant fracture system present. Fracture strikes inferred from AVAZ also correspond with fracture strikes inverted from the microseismic S-wave splitting analysis. Hudson’s crack densities calculated from the AVAZ anisotropic gradients matched crack densities from cross-dipole sonic as well as followed the same trend as the fracture intensities from XRMI data. Part of the success in this case should be attributed to the high-end processing of the input data because such obvious correlations are absent for AVAZ results on sectored PSTM data.
9 October 2023 in Geophysics
As the global need for aluminum constantly rises, bauxite is considered to be a critical mineral, and the mining industry is in search of new and effective exploration solutions. In this context, we design and implement a purely earthquake-based passive seismic survey at the Gerolekas bauxite mining site in Greece. It is a very difficult exploration setting, characterized by rough topography, limited accessibility, and a very complex geotectonic regime. We gather a passive seismic data set consisting of four months of continuous recordings (May to August 2018) from 129 stand-alone 3C seismological stations. We then analyze this data set and extract 848 microearthquakes that will serve as sources for the application of local earthquake tomography (LET) and transient-source seismic interferometry (TSI) by autocorrelation. We apply LET to estimate the 3D P- and S-wave velocity models of the subsurface below the study area and TSI by autocorrelation to retrieve the zero-offset virtual reflection responses below each of the recording stations. The velocity models provide a relatively coarse image of a previously completely unexplored part of the mining concession, whereas the higher-resolution virtual reflection imaging illuminates in detail the different interfaces. We also reprocess three lines of legacy active seismic data that were shot in 2003, using the LET P-wave velocity model for depth migration, and confirm the improvement of seismic imaging. Finally, we evaluate the obtained results using well data and jointly interpret them, extracting useful information on the expected target depths and indicating that earthquake-based passive seismic techniques can be an innovative and environmentally friendly option for mineral exploration.
1 June 2015 in Journal of Applied Geophysics
1 August 2018 in Interpretation
We have tested brittleness prediction by integrating well and 3D seismic data using machine learning (proximal support vector machine algorithm) for Lower Paleozoic shales from the Baltic Basin in northern Poland. The workflow allowed for differentiation of the brittle and ductile zones of the thin shale layers, as well as mapping of the marly formation (fracture barrier) with superior resolution as compared with the resolution of the original input seismic data. The important part of the success was the appropriate definition of the mineralogical brittleness index (BI) tailored to the local geologic conditions. The obtained BI volume outlines the more and less brittle zones in the lower shale unit, i.e., the Sasino Formation, as well as the overlaying unit with high values of BI (Prabuty marls). The mechanical BI based on the Young’s modulus and Poisson’s ratio did not deliver the desired brittleness characterization of the formations of interest, which confirms the weakness of estimating BI using the above geomechanical measurements alone. The weak point of the reported analysis is the small number of available wells, which makes the prediction’s statistics unsatisfactory.