Adilson Yoshio Furuse

Adilson Yoshio Furuse

Auto-generated profile, based on publicly available information

Adilson Yoshio Furuse

Department of Operative Dentistry, Endodontics and Dental Materials, Bauru School of Dentistry, University of Sao Paulo, Bauru, SP, Brazil

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2019 in Journal of Applied Oral Science
Verified
Journal Article
Open access
PDF file
FRFabio Rizzante
Fabio Rizzante
RMRafael Francisco Lia Mondelli
Rafael Francisco Lia Mondelli
AFAdilson Yoshio Furuse
Adilson Yoshio Furuse
ABAna Flávia Sanches Borges
Ana Flávia Sanches Borges
GMGustavo Mendonça
Gustavo Mendonça
SISérgio Kiyoshi Ishikiriama
Sérgio Kiyoshi Ishikiriama
Bulk-fill composites were introduced in dentistry to accelerate clinical procedures while providing adequate outcomes. Concerns regarding the use of bigger composite increments rely on the polymerization shrinkage and shrinkage stress, which may generate gaps on the adhesive interface and result in a reduced success rate. Objective: To evaluate the polymerization shrinkage stress of different bulk-fill resin composites and their elastic modulus. Materials and Methods: Fourteen specimens were made for each of the nine different resin composites (seven with 12 mm3 and seven with 24 mm3): Surefill SDR flow (SDR), X-tra Base (XB), Filtek Bulk Fill Flowable (FBF), Filtek Z350XT Flow (Z3F); Tetric Evo Ceram Bulk Fill (TBF), X-tra Fil (XF), Filtek Bulk Fill (FBP), Admira Xtra Fusion (ADM) and Filtek Z350 XT (Z3XT). Linear shrinkage stress was evaluated for 300 s with the aid of a linear shrinkage device adapted to a Universal Testing Machine. For each composite group, seven additional specimens (2x2x25 mm) were made and Young's modulus was evaluated with a 3-point bending device adapted in a Universal Testing Machine with 0.5 mm/min crosshead speed and 50 KgF loading cell. Results: For 12 mm3 specimens, three-way ANOVA showed that only SDR and TBF generated lower stress after 20 s. Considering 300 s, TBF, SDR, and XF generated the lowest stress, followed by ADM, FBP, XB, and FBF, which were similar to Z3XT. Z3F generated the highest stress values for all time points. Considering 24 mm3 specimens after 20 s, all bulk fill composites generated lower stress than Z3XT, except XB. After 300 s, SDR, FBP, and ADM generated the lowest stress, followed by TBF and XF. For elastic modulus, one-way ANOVA showed that FBF, SDR, Z3F, and ADM presented the lowest values, followed by XB and TBF. FBP, Z3XT, and XF presented the highest elastic modulus among the evaluated composites. Conclusions: Bulk-fill resin composites presented equal to lower shrinkage stress generation when compared to conventional composites, especially when bigger increments were evaluated. Bulk-fill composites showed a wide range of elastic modulus values, but usually similar to “regular” composites.

1 November 2008 in Journal of Dentistry
Verified
Journal Article
Closed access
AFAdilson Y. Furuse
Adilson Y. Furuse
KGKathryn Gordon
Kathryn Gordon
FRFlávia P. Rodrigues
Flávia P. Rodrigues
Nikolaos SilikasNikolaos Silikas
Nikolaos Silikas
DWDavid Christopher Watts
David Christopher Watts

1 January 2014 in Brazilian Dental Journal
Verified
Journal Article
Open access
PDF file
PRPatrício Runnacles
Patrício Runnacles
GCGisele Maria Correr
Gisele Maria Correr
FBFlares Baratto-Filho
Flares Baratto-Filho
CGCarla Castiglia Gonzaga
Carla Castiglia Gonzaga
AFAdilson Yoshio Furuse
Adilson Yoshio Furuse
During the cementation of ceramic veneers the polymerization of resin cements may be jeopardized if the ceramics attenuate the irradiance of the light-curing device. The aim of this study was to evaluate the effect of different types and thicknesses of ceramic veneers on the degree of conversion of a light-cured resin-based cement (RelyX Veneer). The cement was light-cured after interposing ceramic veneers [IPS InLine, IPS Empress Esthetic, IPS e.max LT (low translucency) and IPS e.max HT (high translucency) - Ivoclar Vivadent] of four thicknesses (0.5 mm, 1.0 mm, 1.5 mm and 2.0 mm). As control, the cement was light-cured without interposition of ceramics. The degree of conversion was evaluated by FTIR spectroscopy (n=5). Data were analyzed with one-way ANOVA and Tukey's test (α=0.05). Significant differences were observed among groups (p0.05). Among 1.5-mm-thick veneers, IPS e.max LT was the only one that showed different results from the control (p0.05). The degree of conversion of the evaluated light-cured resin cement depends on the thickness and type of ceramics employed when veneers thicker than 1.5 mm are cemented.

1 January 2010 in Journal of Endodontics
Verified
Journal Article
Closed access
LCLeonardo Fernandes da Cunha
Leonardo Fernandes da Cunha
AFAdilson Yoshio Furuse
Adilson Yoshio Furuse
RMRafael Francisco Lia Mondelli
Rafael Francisco Lia Mondelli
JMJosé Mondelli
José Mondelli

1 December 2014 in The Journal of Prosthetic Dentistry
Verified
Journal Article
Closed access
LCLeonardo Fernandes da Cunha
Leonardo Fernandes da Cunha
LPLorena Oliveira Pedroche
Lorena Oliveira Pedroche
CGCarla Castiglia Gonzaga
Carla Castiglia Gonzaga
AFAdilson Yoshio Furuse
Adilson Yoshio Furuse

1 May 2011 in Dental Materials
Verified
Journal Article
Closed access
AFAdilson Y. Furuse
Adilson Y. Furuse
JMJosé Mondelli
José Mondelli
DWDavid Christopher Watts
David Christopher Watts