2 December 2020 in Geophysical Research Letters
Magma flow, heat conduction, and hydrothermal fluid flow control the heat transfer through the upper crust. Magmatic‐hydrothermal activity is essential for the utilization of geothermal energy, formation of ore deposits, and predictions of volcanic hazards, but the interplay between magmatic and hydrothermal processes is not well constrained due to the lack of adequate scientific tools. Simulation results from our novel coupled numerical model resolving both magma (Navier‐Stokes) and hydrothermal (Darcy) flow quantify the influence of magma convection and rock permeability on energy transfer. Convection of a hot‐dry rhyolitic magma has an accelerating effect of up to 15% on the cooling of the reservoir by enhancing the heat transfer toward the magma‐hydrothermal interface. However, at high permeabilities and high brittle‐ductile transition temperatures, magma flow can also have a secondary decelerating effect, because it prevents efficient permeability creation and entrainment of hydrothermal fluids at the edges of the magma reservoir.
2 June 2017 in Geochemistry, Geophysics, Geosystems
The potential of mining seafloor massive sulfide deposits for metals such as Cu, Zn, and Au is currently debated. One key challenge is to predict where the largest deposits worth mining might form, which in turn requires understanding the pattern of subseafloor hydrothermal mass and energy transport. Numerical models of heat and fluid flow are applied to illustrate the important role of fault zone properties (permeability and width) in controlling mass accumulation at hydrothermal vents at slow spreading ridges. We combine modeled mass‐flow rates, vent temperatures, and vent field dimensions with the known fluid chemistry at the fault‐controlled Logatchev 1 hydrothermal field of the Mid‐Atlantic Ridge. We predict that the 135 kilotons of SMS at this site (estimated by other studies) can have accumulated with a minimum depositional efficiency of 5% in the known duration of hydrothermal venting (58,200 year age of the deposit). In general, the most productive faults must provide an efficient fluid pathway while at the same time limit cooling due to mixing with entrained cold seawater. This balance is best met by faults that are just wide and permeable enough to control a hydrothermal plume rising through the oceanic crust. Model runs with increased basal heat input, mimicking a heat flow contribution from along‐axis, lead to higher mass fluxes and vent temperatures, capable of significantly higher SMS accumulation rates. Nonsteady state conditions, such as the influence of a cooling magmatic intrusion beneath the fault zone, also can temporarily increase the mass flux while sustaining high vent temperatures.
8 July 2024 in Journal of Geophysical Research: Solid Earth
The timing and duration of volatile generation from crystallizing magma reservoirs and fluid release across the magmatic‐hydrothermal interface depend on complex coupled interactions controlled by non‐linear, dynamic properties of magmas, rocks and fluids. Understanding these mechanisms is essential to explain the rare formation of economic porphyry copper deposits. For this study, we further developed a coupled numerical model that can simultaneously resolve magma and hydrothermal flow by introducing a description of fluid transport within the magma reservoir and volatile release to the host rock. Our simulations use realistic magma properties derived from published experimental and modeling studies and cover different magma compositions and water contents. We show that magma convection at melt‐dominated states leads to homogenization, which delays fluid release and promotes a rapid evolution toward a mush state. The onset of magmatic volatile release can be near‐explosive with a tube‐flow outburst event lasting 3.5 wt% H2O that could result in the formation of hydrothermal breccias and vein stockworks or trigger eruptions. This event can be followed by sustained fluid release at moderate rates by volatile flushing caused by magma convection. Subsequent fluid release from concentric tube rings by radial cooling of non‐convecting magma mush with a volume of ∼100 km3 at ∼5 km depth is limited to remaining water contents of ∼3.1 wt% H2O and lasts 50–100 kyr. Ore formation from hydrous magmas may thus involve distinct phases of volatile release.
11 August 2022 in Geochemistry, Geophysics, Geosystems
Faults and fractures can be permeable pathways for focused fluid flow in structurally controlled ore‐forming hydrothermal systems. However, quantifying their role in fluid flow on the scale of several kilometers with numerical models typically requires high‐resolution meshes. This study introduces a modified numerical representation of m‐scale fault zones using lower‐dimensional elements (here, one‐dimensional [1D] elements in a 2D domain) to resolve structurally controlled fluid flow with coarser mesh resolutions and apply the method to magmatic‐hydrothermal ore‐forming systems. We modeled horizontal and vertical structure‐controlled magmatic‐hydrothermal deposits to understand the role of permeability and structure connectivity on ore deposition. The simulation results of vertically extended porphyry copper systems show that ore deposition can occur along permeable vertical structures where ascending, overpressured magmatic fluids are cooled by downflowing ambient fluids. Structure permeability and fault location control the distribution of ore grades. In highly permeable structures, the mineralization can span up to 3 km vertically, resulting in heat‐pipe mechanisms that promote the ascent of a magmatic vapor phase to an overlying structurally controlled epithermal system. Simulations for the formation of subhorizontal vein‐type deposits suggest that the major control on fluid flow and metal deposition along horizontal structures is the absence of vertical structures above the injection location but their presence at greater distances. Using a dynamic permeability model mimicking crack‐seal mechanisms within the structures leads to a pulsating behavior of fracture‐controlled hydrothermal systems and prevents the inflow of ambient fluids under overpressured conditions.