18 September 2018 in Nature Communications
Long-term operational stability is the foremost issue delaying the commercialization of perovskite solar cells (PSCs). Here we demonstrate an in-situ cross-linking strategy for operationally stable inverted MAPbI3 PSCs through the incorporation of a cross-linkable organic small molecule additive trimethylolpropane triacrylate (TMTA) into perovskite films. TMTA can chemically anchor to grain boundaries and then in-situ cross-link to a robust continuous network polymer after thermal treatment, thus enhancing the thermal, water-resisting and light-resisting properties of organic/perovskite films. As a result, the cross-linked PSCs exhibit 590-fold improvement in operational stability, retaining nearly 80% of their initial efficiency after continuous power output for 400 h at maximum power point under full-sun AM 1.5 G illumination of Xenon lamp without any UV-filter. In addition, under moisture or thermal (85 °C) conditions, cross-linked TMTA-based PSCs also show excellent stability with over 90% of their initial or post burn-in efficiency after aging for over 1000 h.
13 May 2013 in Angewandte Chemie International Edition
11 January 2016 in Energy & Environmental Science
This work proposes a novel approach to modulate the nucleation and growth of perovskite crystals in planar perovskite (CH3NH3PbI3−xClx) solar cells by intermixing precursor-capped inorganic nanoparticles of PbS. A small amount of dispersed PbS nanoparticles which were covered with perovskite precursor molecules of methylammonium iodide (CH3NH3I, MAI) through the ligand-exchange treatment functioned as effective seed-like nucleation sites to promote the formation of perovskite lattice structures. Through this intermixing-seeded growth technique, substantial morphological improvements, such as increased crystal domains, enhanced coverage, and uniformity, were realized in the perovskite thin films, and the corresponding solar cell devices exhibited a promising power conversion efficiency of 17.4%, showing an enhancement of approximately 25% compared to that of the controlled pristine solar cell device. The substantially enhanced crystal orientation, particularly along the direction perpendicular to the substrate, was evident from the synchrotron-based grazing incidence wide-angle X-ray scattering data. This observation was consistent with the enhanced carrier diffusion lengths and excellent reproducibility of high fill factors of the planar heterojunction perovskite devices fabricated through the proposed technique.
22 March 2010 in Journal of Materials Chemistry
An imide-functionalized material, poly(oxyethylene)-segmented polymer, was synthesized from the reaction of poly(oxyethylene)diamine of 2000 g mol−1Mw and 4,4′-oxydiphthalic anhydride and used to disperse hybrid nanomaterials of platinum nanoparticles and multi-wall carbon nanotubes (PtNP/MWCNT). The composite material was spin-coated into film and further prepared as the counter electrode (PtNP/MWCNT-CE) for a dye-sensitized solar cell (DSSC). The short-circuit current density (JSC) and power-conversion efficiency (η) of the DSSC with PtNP/MWCNT-CE were found to be 18.01 ± 0.91 mA cm−2 and 8.00 ± 0.23%, respectively, while the corresponding values were 14.62 ± 0.19 mA cm−2 and 6.92 ± 0.07% for a DSSC with a bare platinum counter electrode (Pt-CE). The presence and distribution of PtNP/MWCNT on the CE were characterized by using scanning electron microscopy (SEM), atomic force microscopy (AFM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). The attachment of PtNPs on MWCNTs was observed by transmission electron microscopy (TEM). Cyclic voltammetry (CV), incident-photo-to-current efficiency (IPCE) and electrochemical impedance spectra (EIS) were correlated to explain the efficacy of this nanocomposite system.
7 August 2017 in Advanced Energy Materials
8 September 2017 in ACS Applied Materials & Interfaces