The Tauc plot is a method originally developed to derive the optical gap of amorphous semiconductors such as amorphous germanium or silicon. By measuring the absorption coefficient α(hν) and plotting versus photon energy hν, a value for the optical gap (Tauc gap) is determined. In this way non‐direct optical transitions between approximately parabolic bands can be examined. In the last decades, a modification of this method for (poly‐) crystalline semiconductors has become popular to study direct and indirect interband transitions. For this purpose, (ahν)n (n = , 2) is plotted against hν to determine a value of the electronic bandgap. Due to the ease of performing UV–vis measurements, this method has nowadays become a standard to analyze various (poly‐) crystalline solids, regardless of their different electronic structure. Although this leads partially to widely varying values of the respective bandgap of nominally identical materials, there is still no study that critically questions which peculiarities in the electronic structure prevent a use of the Tauc plot for (poly‐) crystalline solids and to which material classes this applies. This study aims to close this gap by discussing the Tauc plot and its limiting factors for exemplary (poly‐) crystalline solids with different electronic structures.
The synthesis of Mg‐substituted copper hydroxycarbonates by constant‐pH co‐precipitation with subsequent ageing of the precipitate has been studied in detail. This allowed the retrieval of crystalline magnesian malachite samples, which showed a “radical‐sign‐shaped” pH drop and the blue/green color change during ageing that is well‐known from the analogous Cu/Zn system. The crystallization of Cu‐rich samples has been studied elaborately by means of powder diffraction, pair distribution function (PDF), and infrared spectroscopy, thus elucidating the ageing chemistry of Cu,Mg hydroxycarbonates in general. It was found that up to 17 % Mg can be incorporated into the crystalline malachite using a synthesis route comparable to that established for Cu/ZnO catalysts, but with drastically elongated precipitate ageing times. For higher Mg contents, a step‐like pH drop was observed instead, and an amorphous variant of the hydroxycarbonate, referred to as “magnesian georgeite”, could be isolated. From such a Mg‐rich sample (Cu/Mg 70 : 30 at. %), a Cu/MgO catalyst has been prepared that shows high activity and good stability in CO hydrogenation to methanol over 800 hrs. time on stream.
The preparation of Al-doped ZnO via thermal decomposition of crystalline precursors, with a particular emphasis on kinetic effects on the solubility limits, was studied. The promoting effect of Al3+ on the catalyst system is discussed for methanol synthesis where ZnO:Al is employed as a support material for copper nanoparticles. The synthesis of the Al-doped zinc oxides in this study was inspired by the industrial synthesis of the methanol synthesis catalyst via a co-precipitated crystalline precursor, here: hydrozincite Zn5(OH)6(CO3)2. To determine the aluminium speciation and the solubility limit of the aluminium cation on zinc positions, a series of zinc oxides with varying aluminium contents was synthesized by calcination of the precursors. Short precipitate ageing time, low ageing temperature and aluminium contents below 3 mol% metal were advantageous to suppress crystalline side-phases in the precursor, which caused an aluminium segregation and non-uniform aluminium distribution in the solid. Even if zinc oxide was the only crystalline phase, TEM revealed such segregation in samples calcined at 320 °C. Only at very low aluminium contents, the dopant was found preferably on the zinc sites of the zinc oxide structure based on the signal dominating the 27Al NMR spectra. The solubility limit regarding this species was determined to be approximately xAl = 0.013 or 1.3% of all metal cations. Annealing experiments showed that aluminium was kinetically trapped on the site and segregated into ZnAl2O4 upon further heating. This shows that lower calcination temperatures such as applied in catalyst synthesis conserve a higher aluminium doping concentration on that specific site than is expected thermodynamically.
Nano-scale zinc-oxide doped with aluminium ZnO:Al is studied by different techniques targeting surface changes induced by the conditions at which ZnO:Al is used as support material in the catalysis of methanol. While it is well established, that a variety of 1H and 27Al resonances can be found by solid-state NMR for this material, it was not clear yet which signals are related to species located close to the surface of the material and which to species located in the bulk. To this end, a method is suggested which makes use of a paramagnetically impregnated material to suppress NMR signals close to particle surface in the blind-sphere around the paramagnetic metal atoms. It is shown that it is important to use conditions which guarantee a stable reference system relative to which it can be established whether the coating procedure is conserving the original structure or not. This method, called Paramagnetically Assisted Surface Peak Assignment (PASPA), helped to assign the 1H and 27Al NMR peaks to the bulk and the surface layer defined by the blind- sphere of the paramagnetic atoms. The assignment results are further corroborated by the results from heteronuclear 27Al{1H} dipolar dephasing experiments, which indicate the hydrogen atoms are preferentially located in the surface layer and not in the particle core.
5 June 2026 in Colloids and Surfaces A: Physicochemical and Engineering Aspects