Vessen Vassilev

Vessen Vassilev

Auto-generated profile, based on publicly available information

Vessen Vassilev

Microwave Electronics Laboratory, Chalmers University of Technology, Gothenburg, Sweden

Research Focus & Metrics

Academic Career Length

27Years (2000-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 September 2008 in Astronomy & Astrophysics
Verified
Journal Article
Open access
PDF file
VVV. Vassilev
V. Vassilev
DMD. Meledin
D. Meledin
ILI. Lapkin
I. Lapkin
VBV. Belitsky
V. Belitsky
ONO. Nyström
O. Nyström
HOH. Olofsson
H. Olofsson
Astronomy & Astrophysics (A&A) is an international journal which publishes papers on all aspects of astronomy and astrophysics

1 December 2016 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
AVAbbas Vosoogh
Abbas Vosoogh
PKPer-Simon Kildal
Per-Simon Kildal
VVVessen Vassilev
Vessen Vassilev
We present a V-band multilayer corporate-fed slot array antenna with wide impedance bandwidth and high efficiency. The proposed antenna consists of three unconnected metal layers based on the recently introduced gap waveguide technology. A 2 × 2 cavity-backed slot subarray acts as the unit cell of the array. The top metal layer contains the radiating slots, the intermediate layer contains the cavities, formed by pins, and the third layer is the ridge gap waveguide corporate-feed network. The latter is realized by a texture of pins and guiding ridges to uniformly excite the cavities with the same amplitude and phase. The proposed antenna fulfills the radiation pattern requirement of the ETSI 320 standard. A prototype consisting of 16 × 16 slots was manufactured by a fast modern planar 3-D machining method, i.e., die-sink electric discharge machining. The fabricated prototype has a relative impedance bandwidth of 17.6% with input reflection coefficient better than -10 dB. The Eand H-planes radiation patterns satisfy the ETSI class II copolar sidelobe envelope, and the measured cross-polar level is more than -30 dB below the copolar level over the 56-75 GHz frequency band. The measured antenna efficiency is better than 60% over the same band.

11 August 2017 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
FFFangfang Fan
Fangfang Fan
Jian YangJian Yang
Jian Yang
VVVessen Vassilev
Vessen Vassilev
AZAshraf Uz Zaman
Ashraf Uz Zaman
Gap waveguide is a promising transmission structure, especially for millimeter-wave (mmW) and terahertz applications. It does not require conductive connection between the upper and the lower plates, which makes this technology gain advantages over conventional rectangular waveguides and substrate integrated waveguides in an mmW and terahertz regime. Different fabrication methods for gap waveguides should be employed for different frequency bands applied, such as molding, milling, die forming, electrical discharge machining, microelectromechanical systems, and 3-D printing. Therefore, different pin forms used in gap waveguides are required to match the applied fabrication methods. In this paper, a new pin form, the half-height-pin form, in gap waveguides is proposed for reducing the fabrication cost, and its stopband characteristics are investigated and compared with the previous full-height pins in gap waveguides at the V-band. A device of a double-ridged gap waveguide with two 90° bends for verifying the stopband characteristic analysis of the new pin form has been designed and manufactured. The measured data confirm our analysis and simulations.

13 June 2019 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
AVAbbas Vosoogh
Abbas Vosoogh
MSMilad Sharifi Sorkherizi
Milad Sharifi Sorkherizi
VVVessen Vassilev
Vessen Vassilev
AZAshraf Uz Zaman
Ashraf Uz Zaman
Zhongxia Simon HeZhongxia Simon He
Zhongxia Simon He
HZHerbert Zirath
Herbert Zirath
This paper presents the design and realization of a high data rate radio front-end module for point-to-point backhaul links at E-band. The design module consists of four vertically stacked unconnected metal layers without any galvanic and electrical contact requirements among the building blocks, by using gap waveguide technology. The module components are a high-gain array antenna, diplexer, and circuitry consisting of a transmitter (Tx) and a receiver (Rx) monolithic microwave integrated circuits (MMICs) on a carrier board, which is successfully integrated into one package with a novel architecture and a compact form. The diplexer consists of two direct-coupled cavity bandpass filters with channels at 71-76 GHz and 81-86 GHz with a measured return loss of 15 dB and an isolation greater than 50 dB. A wideband $16x16$ slot array antenna with a measured gain of more than 31 dBi is used to provide high directivity. The measured results show that the packaged transmitter provides a conversion gain of 22 and 20 dB at 76 and 86 GHz, respectively, with an output power of 14 and 16 dBm at 1-dB gain compression point, at the same frequencies. The packaged receiver shows an average conversion gain of 20 dB at 71-76-GHz and 24 dB at 81-86-GHz bands. A real-time wireless data transmission is successfully demonstrated with a data rate of 8 Gbit/s using 32-quadrature amplitude modulated signal over 1.8-GHz channel bandwidth with spectral efficiency of 4.44 bit/s/Hz. The proposed radio front end provides the advantages of low loss, high efficiency, compact integration, and a simple mechanical assembly, which makes it a suitable solution for small-cell backhaul links.

3 December 2015 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
SRSofia Rahiminejad
Sofia Rahiminejad
EPElena Pucci
Elena Pucci
VVVessen Vassilev
Vessen Vassilev
PKPer-Simon Kildal
Per-Simon Kildal
SHSjoerd Haasl
Sjoerd Haasl
PEPeter Enoksson
Peter Enoksson
Radiation leakages are a considerable problem when measuring waveguide structures at high frequencies. In order to maintain good electrical contact, flanges need to be tightly and evenly screwed to the device under test. This can be a time-consuming operation, especially with repeated measurements. We present a metamaterial-based adapter, which prohibits leakage even in the presence of gaps at the interconnects. This so-called gap adapter has been fabricated from a metallized polymer (SU8). The reflection coefficient is below -20 dB throughout the band for a 50-μm gap on both sides of the gap adapter. In comparison, a conventional waveguide with a 50-μm gap on both sides has a reflection coefficient of -10 dB. The gap adapter can be used to perform fast measurements, since the normal flange screws are redundant. We compare the SU8 gap adapter with a Si version and to a smooth metal waveguide reference disc. The SU8 gap adapter performed better than the Si version and much better than the waveguide disc in all test cases. SU8 gap adapters were used to measure on a waveguide component. The SU8 gap adapters with 50-μm gaps performed comparable with the waveguide component with the flange screws carefully tightened. The polymer also makes the gap adapter mechanically robust and easy to mass fabricate.

9 June 2016 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
AZAshraf Uz Zaman
Ashraf Uz Zaman
VVVessen Vassilev
Vessen Vassilev
PKPer-Simon Kildal
Per-Simon Kildal
HZHerbert Zirath
Herbert Zirath
This letter demonstrates a packaging concept where a waveguide-to-microstrip transition can be assimilated on a mm-wave MMIC of an arbitrary size and thus avoid the use of bond wires at the high frequency ports of the MMIC circuit. The advantage of the proposed concept is that- it does not require an extra substrate with sub-critical dimensions for the waveguide-to-microstrip transition. The transition can be integrated onto the MMIC, and thus the MMIC can be coupled directly to the waveguide. A Perfect Magnetic Conductor (PMC) surface is used to suppress the unwanted waveguide mode coupling to the oversized circuit cavity. The measured back-to-back transition works over the frequency band 66-98 GHz (relative BW of 38%) with minimum return loss of 12.7 dB. The total insertion loss of the manufactured prototype is found to be 3.26 dB, which also includes a 14.8 mm long microstrip line on an Alumina substrate. The losses in a single transition vary between 0.25 and 0.42 dB.