10 May 2019 in IEEE Journal of Solid-State Circuits
This paper presents the first 28-/37-/39-GHz linear Doherty power amplifier (PA) in silicon for broadband fifth-generation (5G) applications. We introduce a new transformer-based on-chip Doherty power combiner that can reduce the impedance transformation ratio (ITR) in power back-off (PBO) and, thus, improve the bandwidth and power-combining efficiency. We also devise a ``driver-PA co-design'' method that creates power-dependent uneven feeding in the Doherty PA and enhances the Doherty operation without any hardware overhead or bandwidth compromise. For the proof of concept, we implement a 28-/37-/39-GHz PA fully integrated in a standard 130-nm SiGe BiCMOS process, which occupies 1.8 mm². The PA achieves a 52% -3-dB small-signal S₂₁ bandwidth and a 40% -1-dB large-signal saturated output power (Psat) bandwidth. At 28/37/39 GHz, the PA achieves +16.8-/+17.1-/+17-dBm Psat, +15.2-/+15.5-/+15.4-dBm P1,dB, and superior 1.72/1.92/1.62 times efficiency enhancement over class-B operation at 5.9-/6-/6.7-dB PBO. Moreover, the PA demonstrates multi-gigabit-per-second data rates with excellent efficiency and linearity for 64-quadrature amplitude modulation (64-QAM) in three millimeter-wave (mm-wave) 5G bands. This PA advances the state of the art for Doherty, wideband, and 5G silicon PAs in mm-wave bands. It supports drop-in upgrade for current PAs in existing mm-wave systems and opens doors to compact system solutions for future multiband 5G massive multiple-input multiple-output (MIMO) and phased-array platforms.
22 June 2021 in IEEE Journal of Solid-State Circuits
This article presents a broadband power amplifier (PA) with a distributed-balun output network that provides the PA optimum load impedance over a wide bandwidth. The proposed output network comprises two coupled-line sections and absorbs the device output capacitance. It employs a scalable coupled-line modeling approach that captures both the magnetic (inductive) and electric (capacitive) couplings between windings with fewer parameters and supports a rapid design process. Closed-form design solutions, design space limitations, bandwidth limits, and design tradeoffs are derived and analyzed comprehensively. Its extension to differential output and common-mode response is also discussed in detail. As a proof of concept, a prototype PA is implemented for multiband fifth-generation (5G) applications in 45-nm SOI CMOS. With no biasing retuning or network reconfiguration, the PA consistently achieves >19.1 dBm P sat , >37.3% peak power-added efficiency (PAE), 17.8-19.6 dBm P 1dB , and 36.6%-44.3% PAE P1dB over 24-40 GHz, verifying the truly wideband large-signal matching. The PA demonstrates 5G new radio (NR) frequency range 2 (FR2) modulation signals over 24-42 GHz, covering n257/n258/n260 5G bands. For 5G NR FR2 800-MHz 2-CC 64-QAM signals (11.78-dB PAPR), the PA achieves 11.3-dBm/16.6% average P out /PAE with -25.1-dB rms EVM at 28-GHz and 10.2-dBm/13.6% average P out /PAE with -25.1-dB rms EVM at 37 GHz.
4 May 2021 in IEEE Journal of Solid-State Circuits
Silicon-based millimeter-wave (mm-Wave) power amplifiers (PAs) with high power and high peak/back-off efficiency are highly desired to efficiently amplify multi-Gb/s 5G NR signals. This article presents a fully integrated high-power broadband linear Doherty PA with multi-primary distributed-active-transformer (DAT) power combining. We introduce a transformer-based impedance inverter for active load modulation and a multi-primary DAT structure for hybrid series and parallel power combining. Based on this, we propose a transformer-based Doherty combiner with more design freedom and a multi-primary DAT-based Doherty PA for simultaneous active load modulation and low-loss power combining. The EM simulation results demonstrate that the proposed DAT-based Doherty output network achieves very symmetric and balanced load impedances among all the main and auxiliary PA ports. As a proof of concept, a 24-30-GHz prototype PA is implemented in a 0.13- μm SiGe BiCMOS process. The PA achieves 30.4% PAE max , 28.3-dBm P sat , 30.2% PAE at 26.8-dBm P 1 dB , and 21.2% PAE at 6-dB back-off from P sat at 28 GHz. Modulation measurement with single-carrier 64-QAM signals and 5G NR FR2 orthogonal frequency-division multiplexing (OFDM) signals has been demonstrated. For a 200-MHz 1-CC 5G NR FR2 64-QAM signal, the PA achieves 18.1-dBm P avg and 13.8% PAE avg with -25.1-dB rms EVM at 28 GHz.
25 October 2019 in IEEE Journal of Solid-State Circuits
8 February 2019 in IEEE Journal of Solid-State Circuits
This paper presents a noise circulating cross-coupled voltage-controlled oscillator (VCO) topology with a transformer-based tank. The introduced noise circulating active core greatly suppresses the effective noise power from the active devices while offering the same amount of negative resistance compared to conventional cross-coupled VCO topologies. The mechanism of noise circulation is investigated with theoretical analysis and further verified by simulation. Due to the broadband nature of the noise circulating technique, the resulting VCO phase noise in both 1/f² and 1/f³ regions is greatly improved over a wide frequency tuning range. A prototype VCO at 2.35 GHz is implemented in a standard 130-nm bulk CMOS process with 0.36-mm² core area. It draws 2.15 mA from a 1.2-V supply. The measured figure-of-merit (FoM) is 193.1/195.0/195.6 dBc/Hz at 100k/1M/10MHz offsets with a 1/f³ phase noise corner of only 50 kHz. The VCO design consistently achieves >192.8 dBc/Hz FoM at 100k/1M/10MHz offsets and <60 kHz 1/f³ phase noise corner over its entire 18.6% frequency tuning range (2.05 - 2.47 GHz). It also exhibits low supply frequency pushing of -25 and -13 MHz/V at the highest and lowest frequencies, respectively.
16 April 2019 in IEEE Transactions on Microwave Theory and Techniques