Partial shading is one of the certain conditions in photovoltaic (PV) power plants. Often the panels get partially shaded due to soiling, clouds, and trees. The effect of shading is of high concern and importance especially in applications such as water pumps due to agricultural environments in which they are employed in. However, the research focus on PV fed pumps till date has been restricted to only uniform shading conditions. Unlike uniform shading conditions during maximum power tracking where the panel voltage remains almost constant for an entire range of irradiance, partial shading conditions offer such as highly variable panel voltage, transitions of intermediate DC-DC power converter from continuous conduction mode to discontinuous conduction mode. These effects severely affect the performance of the power converter and therefore the power output of the pump. This paper presents a study on the effects caused by partial shading conditions on pumps through simulations and verified by experimentations. The simulation and experimental results are found to be in good agreement with each other. This research work thus helps in understanding the detrimental effects casued by partial shading conditions and thus serves as a reference tool for practitioners who wish to study PV fed pumps.
4 October 2018 in IEEE Transactions on Energy Conversion
Characteristics of photovoltaic arrays exhibit multiple peaks under mismatching conditions. In order to harness maximum energy, it is imperative to track the global maximum power point. A novel global peak tracking algorithm is proposed using current control in this manuscript. The proposed method operates in backward phase and forward phase to track the global peak. The objective of the proposed algorithm is to track the global maximum accurately with minimum tracking time. The enhanced performance of the proposed algorithm is verified using simulations by comparing it with an existing method. Experimental validation is done using a solar array simulator, boost converter, resistive load and dSPACE controller. Experimental results are in close agreement with simulation. The proposed algorithm is intended to track the global peak of a PV string which contains a group of modules.
29 July 2024 in IEEE Transactions on Circuits and Systems II: Express Briefs
A converter with high voltage gain is generally necessary for interfacing the photovoltaic (PV) systems with grid. However, more semiconductor components are needed to obtain a higher voltage gain, which results in increased losses. This article proposes a novel non-isolated cubic boost (NNICB) DC-DC converter for high-voltage PV applications with a wide voltage gain at a lower duty ratio. Compared to traditional high-gain DC-DC converter, the NNICB converter counters the drawbacks of increased component count and high voltage stress. The NNICB DC-DC converter has a continuous source current for PV applications with low-voltage stress across the diodes and switches. A detailed steady-state analysis of the NNICB topology is carried out for the ideal and non-ideal models, and their corresponding voltage gain equations are computed. Furthermore, the analysis is performed using MATLAB/Simulink and is validated using a 230 W laboratory prototype. The experimental results show that the efficiency of the proposed NNICB topology is 94.42% with a voltage gain of 10.5 at 45% duty ratio. This proves the superior performance of the proposed novel converter in comparison with the existing topologies.
16 October 2018 in IEEE Transactions on Circuits and Systems II: Express Briefs
Small signal models are of high importance in power electronic systems which exhibit highly non-linear properties. They provide access to stability and help in tuning controllers. Small signal models for many power electronic converters are seen in the literature. However, specific applications like photovoltaic systems demand the addition of a capacitor at the terminals of PV panel. Since this capacitor is connected between the PV panel terminals and the input of power converter, it is termed as input capacitor. The effect of the addition of input capacitor on system stability has not been addressed yet. In this brief, we derive the small signal models for PV fed boost converter operating in both continuous conduction mode (CCM) and discontinuous conduction modes (DCM) of operation. The load is assumed as purely resistive; however, the analysis holds good for any practical loads. It is observed that in both CCM and DCM the stability of the maximum power point tracking (MPPT) system is independent of the input capacitance. It is also shown that the MPPT system is open loop stable for all operating conditions. The studied models are further validated with the experimental setup.
24 August 2018 in IEEE Transactions on Circuits and Systems II: Express Briefs
Detection of maximum power point (MPP) is one of the most sought-after topics in the field of photovoltaic systems. There are many approaches to detecting MPP, amongst these are analytical methods. Analytical methods use mathematical functions to solve the given problem and therefore are one of the dominant strategies. However, their applications to detect MPP have been limited to study only uniform shading conditions. The use of analytical methods to detect MPP for more challenging cases like partial shading conditions is yet to be investigated. In this brief, an analytical solution to identify MPP under partial shading conditions is proposed. Equations describing PV panels and MPP conditions are derived by applying fundamental circuit laws. The derived equations are non-linear and can be solved using numerical techniques available in most of the simulation packages. The proposed model can theoretically detect the MPP amongst ‘N’ peaks. The results from the simulation are verified by conducting experimentation with standard algorithms available in the literature. The results from simulation and experimentation are found to agree with each other.
30 October 2023 in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
In this paper, grid interactive photovoltaic (PV) system is designed for an electric vehicle (EV) charging application and stability of the system is analyzed. The small signal model for the system is derived by averaging and linearizing the state space equations and the condition for stable operation of PV integrated charger system is identified from the transfer functions. The proposed charger system implements a coordinated control between the converters to maintain a power balance between the sources and load. System stability is examined using root-locus plots and in addition, the controller is designed to improve the overall stability and reliability of the system. The proposed method provides a general framework for modelling EV charging systems which also details the importance of deriving the model with multiple energy sources. Further, proposed topology has bi-directional capability, which transfers excess PV power to the grid during off-charging hours. The efficacy of the proposed method is verified using the MATLAB Simulink environment for the different scenarios i.e., variation in the irradiation and disturbances in the grid voltage. The experimental study is conducted on a 1.5 kW laboratory prototype using a low-cost digital signal processing (DSP) controller (launchpad TMS320F28027F) and the measured results authenticate the simulation findings.