12 January 2023 in ISPRS Journal of Photogrammetry and Remote Sensing
5 December 2023 in ISPRS Annals of the Photogrammetry, Remote Sensing and Spatial Information Sciences
Topo-bathymetric laser scanning featuring high spatial resolution and a seamless transition within the littoral zone from land to water evolved considerably in the last decade due to progress in both sensor technology and processing methods. Unlike early systems that focused solely on maximizing depth of penetration, topo-bathymetric scanners enable detailed description of coastal and inland waters at a level of detail that opens up applications in hydromorphology, hydraulic engineering, ecohydraulics, and hydrobiology. Since 2013, a near-natural river section of the pre-alpine Pielach River has been repeatedly surveyed with bathymetric LiDAR sensors from manned and unmanned aerial platforms. The captured time series not only constitutes a valuable data basis for analyzing morphometric change in response to recurring flood peaks, but also allows to trace the progress in sensor, platform and data processing technology. In this contribution we demonstrate that over the last ten years, the depth performance could be increased by approximately 60 %, starting from 1 Secchi depths to more than 2 Secchi depths with sub-m spatial resolution. We furthermore focus on current approaches for improving the geometric sensor calibration, which allow integrated processing of GNSS-, IMU- and LiDAR observations for concurrent calculation of both flight trajectories and 3D point clouds with an absolute accuracy better than 5 cm. This is specifically important for repeat surveys and monitoring of fluvial processes. While this contribution confirms substantial progress in the field, further topics like precise modeling of dynamic water surfaces, full waveform processing in complex target situations including littoral vegetation and submerged deadwood, and detection and modeling of underwater vegetation are identified as future research areas.
3 July 2024 in ISPRS Journal of Photogrammetry and Remote Sensing
19 October 2023 in The International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences
Driven by developments in the automotive industry, the availability of compact consumer-grade LiDAR (Light Detection and Ranging) sensors has increased significantly in recent years. Some of these sensors are also suitable for UAV-based surveying tasks. This paper first discusses the differences between consumer-grade and survey-grade LiDAR systems. Special attention will be paid to the scanning mechanisms used on the one hand and to different solutions for the transceiver units on the other hand. Based on the technical data of two concrete systems, the consumer-grade DJI Zenmuse L1 sensor and the survey-grade scanner RIEGL VUX-1UAV, the expected effects of the sensor parameters on the 3D point cloud are first discussed theoretically and then verified using an exemplary data set in Hessigheim (Baden-Württemberg, Germany). The analysis shows the possibilities and limitations of consumer-grade LiDAR. Compared to the low-cost sensor, the high-end scanner exhibits lower range measurement noise (5–10 mm) and better 3D point location accuracy. Furthermore, the higher laser beam quality of high-end devices (beam divergence, beam shape) enables more detailed object detection at the same point density. With moderate accuracy requirements of 5–10 cm, however, applications in the geodetic-cartographic context also arise for the considerably less expensive consumer-grade LiDAR systems.
27 March 2025 in ISPRS Journal of Photogrammetry and Remote Sensing
19 October 2023 in The International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences
Airborne laser scanning allows for efficient acquisition of accurate 3D data for large areas. Because georeferencing of the LiDAR data requires knowledge of the platform trajectory, the laser scanner system commonly comprises a global navigation satellite system (GNSS) receiver/antenna and an inertial measurement unit (IMU). The standard processing pipeline consists of GNSS/IMU integration, georeferencing, and subsequent adjustment of the laser data. Here, we consider a holistic GNSS/IMU/LiDAR-integration approach based on least-squares adjustment. The GNSS is loosely coupled, and the GNSS positions are obtained using either postprocessing kinematic or precise point positioning GNSS processing strategies using the open-source software RTKLib. In this contribution, we compare the resulting point clouds to those of a standard processing workflow and evaluate the impact of the different processing strategies on point cloud quality in terms of internal consistency and absolute accuracy for a airborne laser bathymetry (ALB) dataset. Although the GNSS solutions themselves differ strongly, both the PPK- and the PPP-derived point clouds show better strip differences (below 2.5 cm) and similar absolute accuracy (<4 cm RMSE w.r.t. reference targets after correction of constant datum shift) compared to the reference solution.