Three new benzothiadiazole (BTD)-containing luminophores with different configurations of aryl linkers have been prepared via Pd-catalyzed cross-coupling Suzuki and Buchwald–Hartwig reactions. Photophysical and electroluminescent properties of the compounds were investigated to estimate their potential for optoelectronic applications. All synthesized structures have sufficiently high quantum yields in film. The BTD with aryl bridged carbazole unit demonstrated the highest electrons and holes mobility in a series. OLED with light-emitting layer (EML) based on this compound exhibited the highest brightness, as well as current and luminous efficiency. The synthesized compounds are not only luminophores with a high photoluminescence quantum yield, but also active transport centers for charge carriers in EML of OLED devices.
Polymer composites based on poly(N,N′-bis-4-butylphenyl-N,N′-bisphenyl)benzidine (poly-TPD) with PCBM and copper(II) pyropheophorbide derivative (Cu-PP) were developed. In thin films of the poly-TPD and Cu-PP composites, the charge carrier mobility was investigated for the first time. In the ternary poly-TPD:PCBM:Cu-PP composite, the electron and hole mobilities are the most balanced compared to binary composites and the photoconductivity is enhanced due to the sensitization by Cu-PP in blue and red spectral ranges. The new composites are promising for use in the development of photodetectors.
Using palladium-catalyzed Suzuki polycondensation, we synthesized new light-emitting fluorene copolymers containing the dicyano derivatives of stilbene and phenanthrene and characterized them by gel permeation chromatography, UV-vis absorption spectroscopy, spectrofluorimetry, and cyclic voltammetry. The photoluminescence spectra of the synthesized polymers show significant energy transfer from the fluorene segments to the dicyanostilbene and 9,10-dicyanophenanthrene units, which is in agreement with the data of theoretical calculations. OLEDs based on these polymers were fabricated with an ITO/PEDOT-PSS (35 nm)/p-TPD (30 nm)/PVK (5 nm)/light emitting layer (70–75 nm)/PF-PO (20 nm)/LiF (1 nm)/Al (80 nm) configuration. Examination of their electroluminescence revealed that copolymers of fluorene with dicyanostilbene show yellow-green luminescence, while polymers with 9,10-dicyanophenanthrene have a greenish-blue emission. The 9,10-dicyanophenanthrene units have a more rigid structure compared to dicyanostilbene and, in OLEDs based on them, an increase in maximum brightness is observed with an increase in the content of the additive to the polymer chain. In particular, the device using fluorene copolymer with 9,10-dicyanophenanthrene (2.5 mol%) exhibited a maximum brightness of 9230 cd/m2 and a maximum current efficiency of 3.33 cd/A.
1 January 2021 in Inorganic Materials: Applied Research
The effect of addition of J-aggregates of polymethine dye into the hole-transport layer of an organic light-emitting diode (OLED) on its characteristics and operational stability was studied. Water-soluble PEDOT:PSS (poly(3,4-ethylenedioxythiophene)) and the interpolymer complex of polyaniline and poly(2-acrylamido-2-methyl-1-propanesulfonic acid) (PAn-PAMPSA) were used as the matrices of polymer nanocomposites. The highest efficiency characteristics of the OLEDs with the considered structure were achieved using PAn-PAMPSA at a particular component ratio in the interpolymer complex. Additives of J‑aggregates did not significantly affect the efficiency characteristics of the OLEDs; however, an increase in the operational stability of devices was recorded.
Cu (II) protoporphyrin Cu-PP-IX and chlorin Cu-C-e6 were found to have both thin solid film formation and charge carrier transport abilities. In the layers deposited by resistive thermal evaporation, the mobilities of holes and electrons are on the order of 10−5 cm2 V−1 s−1. Organic light-emitting diodes incorporating the dye molecules as emitting dopants demonstrate electroluminescence in the UV and near-IR ranges.
6 April 2024 in Journal of Applied Polymer Science