28 February 2020 in Applied Physics Express
19 April 2021 in Applied Physics Letters
To reduce the threshold current density (Jth) of ultraviolet (UV)-B AlGaN-based laser diodes, we investigated the critical parameters aiming to increase the injection efficiency ηi and the optical confinement factor Γ. Optimization of the thickness of the waveguide layer, the average Al content of the p-type AlGaN cladding layer, and the film thickness of the cladding layer demonstrated that the device characteristics can be improved. This optimization achieved a reduction in Jth to 13.3 kA cm−2 at a lasing wavelength of 300 nm, thus offering the lowest Jth value yet achieved for a UV-B laser diode.
29 June 2020 in Applied Physics Express
13 May 2019 in Applied Physics Letters
In this study, we investigated laser characteristics via photoexcitation and electro-optical characteristics via current injection in ultraviolet (UV)-B laser diodes. To achieve light confinement and high current injection, an Al composition-graded 260-nm thick p-type Al0.9→0.45Ga0.1→0.55N cladding layer was designed, which exhibited a calculated light confinement factor of 3.5%. Laser oscillation with a threshold at 275 kW/cm2 at 297 nm was obtained via the photoexcited measurement. A prototype device for current injection was designed using the p-Al0.9→0.45Ga0.1→0.55N cladding layer and an additional Al composition-graded 75-nm thick p-type Al0.45→0Ga0.55→1N layer for the p-type contact layer. The maximum current density in the device reached 41.2 kA/cm2, which is the highest ever reported value among light-emitting devices operating in the UVB and ultraviolet-C regions. The peak wavelength of the emission spectrum obtained from the mirror facet was 300 nm, corresponding to the double quantum wells, without any significant droop. Further, a subpeak emission at 275 nm was observed, which is likely caused by the waveguide layer by electron overflow.
6 March 2023 in Applied Physics Letters
We fabricated sub-230-nm (far UV-C) light emitting diodes (LEDs) on a single-crystal AlN substrate. With 20 quantum well cycles implemented to enhance carrier injection into the active layers, over 1-mW output power (1.4 and 3.1 mW for 226- and 229-nm LEDs, respectively) was obtained under 100-mA operation. The maximum output power reached 21.1 mW for the single-chip 229-nm LED operating at 700 mA, without significant drooping. The forward voltage for both sub-230-nm LEDs operating at 100 mA was low (5.9 V) due to their low resistances and ideal Ohmic contacts between metal and semiconductor components. Additionally, wall plug efficiencies were 0.24% and 0.53% for the 226- and 229-nm LEDs, respectively. The lifetime of the 226-nm LED while operating at 25 °C reached over 1500 h and did not show current leakage, even after 1524 h. This long lifetime will be achieved by improving carrier injection due to many quantum wells, using a high-quality AlN substrate and achieving high wall plug efficiency.
23 May 2019 in Japanese Journal of Applied Physics
We investigated the etching rate of the m-plane of AlGaN by wet etching with tetramethylammonium hydroxide aqueous solutions (25 wt%, 85 °C). After dry etching was performed along the m-plane of AlGaN, wet etching was performed to stably form the m-plane facet of AlGaN. Also, the etching rate increases as the increased AlN molar fraction. In the case of forming a heterojunction such as a UV light-emitting diode, by performing wet etching for 5 min, the flat m-plane facets were formed even though there was a large dependence in AlN molar fraction. These facets were almost vertical and flat with respect to the c-plane, so it has the potential for the use as laser mirror. Also, no change in current density–voltage characteristics was confirmed after the wet etching. Therefore, this method is effective for deep UV laser diode fabrication technology on sapphire substrate.