24 May 2018 in IEEE Transactions on Industrial Electronics
Photovoltaic cells require of Maximum Power Point Tracking (MPPT) algorithms to ensure the amount of power extracted is maximized. True seeking, direct duty cycle control MPPT algorithms are a simple and straightforward solution that can provide high tracking efficiency. In these algorithms the duty cycle is traditionally modified to reach a new steady state prior performing a new MPPT iteration. Therefore, the MPPT update period must be larger than the converter's settling time to reach a new steady state, which limits the dynamic tracking performance. This work proposes a novel direct duty cycle control method that does not require the converter to achieve steady state in between MPPT updates. The proposed method benefits from the natural oscillations occurring in the converter to obtain extreme dynamic tracking improvements while maintaining simple implementation with no need of employing temperature or irradiance sensors. The scheme being introduced combines MPPT concepts with large-signal geometric control to achieve a reliable, high-performance solution very suitable for applications with rapidly changing irradiance such as wearable technology and rooftop EV. The theoretical analysis is supported by detailed mathematical procedures and validated by simulations and experimental results.
21 December 2017 in IEEE Transactions on Power Electronics
LLC resonant converters have gained popularity in a wide number of industrial applications due to their high efficiency and power density. Common applications of this converter are battery chargers, electric vehicles and high efficiency power supplies which require tight output voltage regulations. However, traditional averaging techniques employed in PWM converters cannot be employed for LLC's. As consequence, designing linear controllers for this type of converters requires of complex analysis or applying empirical methods. This paper proposes a simple and straightforward methodology for designing linear controllers for LLC resonant converters. A dual-loop control scheme including an inner current loop and outer voltage loop is introduced. A simplified second order equivalent circuit is employed to derive all the relevant equations for designing the compensators. Simulations and experimental results using a 150 W platform are employed to validate the theoretical analysis.
3 August 2022 in IEEE Transactions on Smart Grid
Since microgrids with renewable generation and energy storage can achieve high reliability, they present an attractive solution for powering critical loads. Microgrids should be carefully planned and optimized to meet the power requirements of critical loads and justify their economic viability. Conventional microgrid design approaches consider a fixed power architecture, focusing mainly on improving the financial aspects of the design by sizing its energy sources. This paper introduces a new Vectorial Microgrid Optimization (VMO) design method for critical loads. The proposed VMO improves the microgrid design by 1) incorporating the selection of the microgrid power conversion architecture and the size of the energy sources into a unified design strategy, 2) implementing multi-objective optimization to find the desired balance between the microgrid power supply availability, net present cost, and power efficiency. Through the use of graph theory, the proposed VMO automates the architecture selection process. The benefits of the proposed VMO method are highlighted in a critical load case-study to find the optimal microgrid design. The obtained microgrid design is compared with the results of existing microgrid planning tools and the standard industry approach for powering critical loads.
26 October 2018 in IEEE Transactions on Power Electronics
Dc microgrids interconnect load-end converters and distributed renewable energy sources within efficient and reliable networks that can operate independently from the main grid. When load-side converters tightly regulate their output voltages, they behave as constant power loads (CPLs), which can cause instability within the network. Traditionally, the stability of CPL-loaded dc microgrids relies on the addition of passive elements, usually leading to dc-bus capacitance increase. In these scenarios, source-end converters controllers are usually linear dual PI compensators, which exhibit a limited dynamic response. State-plane-based controllers have been proposed to improve the dynamic response of stand-alone power converters loaded by CPLs. However, the microgrid problem has not been studied thoroughly. This work proposes the use of a fast state-plane controller to replace one of the system's source-side controllers in order to improve three aspects of the microgrid operation: resiliency under CPL's changes, load transient voltage regulation, and voltage transient recovery time. Since the converter is operating within a microgrid, the controller incorporates a traditional droop rule to enable current sharing with the rest of the converters of the network. Simulations and experimental results of a microgrid with three converters feeding a CPL are provided for different transients.
6 October 2021 in IEEE Transactions on Industrial Electronics
Three-phase pulsewidth modulated converters are usually controlled to achieve sinusoidal currents in the grid side and tight voltage regulation in the dc-link capacitor. The implementation of linear controllers based on small-signal models is a well-established solution for these converters. However, the dynamic performance can be improved only to a limited extent and it deteriorates under different operating conditions which may result in the uncontrollability of the dc-bus voltage during transients. In this work, a state-plane model and control strategy are introduced to improve the dc-link dynamics for three-phase converters. The proposed method provides fast, reliable, and consistent transient responses under the entire operating range, including rectifier and inverter modes. First, a normalized model that describes the natural dynamic behavior of the converter is derived and represented in the state-plane. In this way, the dynamic evolution of the operating point is described in a graphical domain as circular trajectories with well-defined characteristics. The insight provided by these natural trajectories is used to develop a control strategy to improve the dc-link dynamics by selecting a unique combination of circular paths to solve the transients. As a result, the operating point follows well-defined trajectories to achieve fast and consistent dc-link voltage responses under a wide operating range. The effectiveness and feasibility of the proposed control strategy are validated by several simulation and experimental results.
24 June 2024 in IEEE Transactions on Power Electronics
Tracking efficiency, cost, and reliability are important factors when selecting photovoltaic (PV) architectures and converter topologies. PV systems require power converters to maximize power extraction, for which dc–dc converters are a common choice. Differential power processing (DPP) architectures can achieve higher efficiencies and lower cost by reducing the amount of power passing through these converters, while still providing maximum power point tracking (MPPT) capabilities. Single-phase grid connected PV systems, which are the most popular choice in residential applications, require a large capacitance in the dc bus to minimize the voltage ripple caused by double-line pulsating power, impacting the cost and reliability of the system. This work introduces a new MPPT mode of operation for flyback converters in DPP architectures. The proposed MPPT method shows extremely fast dynamic performance and it is capable of maximizing the power extraction even for extreme variations in the bus voltage. In this way, the method enables a significant reduction in the dc bus capacitance, reducing costs, and facilitating the use of ceramic capacitors, while maintaining excellent tracking efficiency. The analysis incorporates comprehensive models that characterize the large-signal dynamic behavior of ideal and nonideal flyback converters, and it is supported by detailed mathematical procedures. The system performance behavior, and limits are validated through simulation and experimental results.