1 January 2013 in Journal of Water Resources Planning and Management
Traditional water distribution simulations, known as demand-driven analysis (DDA), are normally analyzed under the assumption that nodal demands are known and satisfied. The DDA is valid under normal conditions and in design requirement. However, in situations such as pipe burst or pump outage, the outflows at nodes affected by low pressures will decrease. Therefore, network simulation under deficient pressure conditions using conventional DDA can cause large deviation from actual situations. The purpose of this paper is to analyze different compositions of nodal outflow, including volume-driven demand, pressure-dependent demand and leakage to simulate deficient network performance more realistically. An extension of the modeling package EPANET, which implements repetitive modifications to nodal outflows based on pressure-dependent demand formulations and leakage models (EPANET-MNO), is first developed. Then, a comparison is made between the respective performances of four different pressure-depen...
1 May 2018 in Journal of Water Resources Planning and Management
The design of district metered areas (DMAs) has many factors to be considered to reduce the adverse effect of the closure of valves. A three-step methodology for DMA design is proposed based on spectral clustering algorithm and graph theory. The first step is to calculate the nontrivial eigenvectors based on a weighted graph of the water distribution network. The second step is optimal nodes clustering as DMAs by spectral clustering. The third step is to determine the location of meters and valves by a proposed heuristic method. The multicriteria decision method is then used to determine the best DMAs solution. A simple example network is used to demonstrate the method, and a real-world network, the Wolf-Cordera Ranch, is applied to test the feasibility and effectiveness of the proposed method for DMA design in actual systems. Results show that the proposed method can identify different DMA solutions effectively, and better DMA design can be obtained considering different performance criteria.
1 August 2020 in Journal of Water Resources Planning and Management
Partitioning a water distribution system (WDS) into district metered areas (DMAs) is a difficult task due to the complex WDS structure and simultaneous consideration of multiple constraints. Further, alternative metrics can define DMA goals, and expressing and quantifying those objectives in an efficient algorithm is also challenging. To address the multifaceted set of objectives, a multiphase DMA design method is developed. DMA feed pipes are identified as the primary flow paths in a branched network. In the methodology presented here, the feed pipe network is first laid out by determining node clusters and boundary pipes that maximize the dissimilarity of pressures and modularities between clusters and minimize the number of cuts between clusters while defining the number of DMAs closest to the desired number. In the methodology’s second phase, secondary DMA feed pipes are identified by minimizing the number of secondary feed pipes and maximizing the nodal excess energy while maintaining desired pressure. Finally, a postoptimization analysis compares the performance of the Pareto solutions based on their availability, water quality, and daily leakage. System availability is calculated based on the minimum cut-set method combined with a new pressure-driven analysis method. To accelerate the optimization algorithm, two strategies are applied: step-by-step optimization and reducing the decision variable searching space by considering desirable DMA characteristics. The effectiveness of the methods is examined by applying it to the C-Town and real B-Town water distribution networks. Results demonstrate that the search space reduction method effectively decomposes the full network into DMAs in the face of multiple hydraulic and water quality metrics.
1 January 2017 in Procedia Engineering
25 November 2021 in Journal of Water Supply: Research and Technology—AQUA
The consideration of isolation valves and segments is essential for evaluating the water service and resilience of water distribution systems when shutdowns are required under pipe failure. However, little work has been done on assessing the resilience response and intervention based on segments. This study investigates the impact of intervention (valve density and protection of critical segment) and response (recovery time and recovery sequence) on system resilience taking valve layout into consideration. An algorithm to identify segments based on the graph theory is proposed. Resilience is quantified using the satisfactory rate of the water supply demand. Critical segments are ranked based on resilience analysis. The resilience evaluation method is applied to a case study network. It is found that valve optimization can significantly reduce the number of valves without considerably decreasing the resilience performance. Valve density and the protection of critical segment can reduce the severity of pipe failure, while efficient recovery response can reduce the severity and shorten the duration of pipe failure simultaneously. The criticality of segments depends on the segment location and hydraulic interdependency among segments.
30 May 2023 in Water Research