Aromatic solvents, such xylene and toluene, are widely used in the organic damage removal operations, although increasing environmental requirements have encouraged the research for new environmental-friendly solutions to replace these solvents. Microemulsions are thermodynamically stable multicomponent systems known by their notable solubilization capability. This paper describes the preparation and investigation of a low-oil-content microemulsion system able to remove the organic damage and restore the permeability. The damage removal efficiency, for the microemulsion systems prepared, was comparable to xylene. The results showed that the proposed microemulsion formulation is a cost-effective and environment-friendly alternative to aromatic solvents.
30 October 2023 in International Journal of Chemical Engineering
Although biodiesel production is undoubtedly a mature technology, there are still ways to improve it, especially through process intensification. The present study investigated the esterification of oleic acid with ethanol for biodiesel production in a nonconventional atomization reactor. The effects of the oleic acid flow rate (1.3, 2.6, and 3.9 g/min), atomization pressure (50, 100, and 150 kPa), and temperature (323, 333, and 343 K) were evaluated by a complete factorial experimental design. The size of droplets was determined by computational image processing. A mathematical model was also developed to describe the conversion of oleic acid to ethyl ester as a function of molar concentration of components and operating conditions of the reactor. A hybrid estimation of parameters (pre-exponential factor, activation energy, and equilibrium and solubility constants) was performed using particle swarm optimization followed by the Broyden–Fletcher–Goldfarb–Shanno method. The Pareto analysis has shown that the increase in temperature in the reactor and the increase in atomization pressure have improved the conversion of oleic acid. Higher pressure values in the atomization nozzle led to the generation of small oleic acid droplets, which accelerated reagent consumption during the reaction. On the other hand, conversion values were reduced by increasing the oleic acid flow rate. The highest conversion of oleic acid (86.7%) was obtained under the following reaction conditions: temperature of 343 K, atomization pressure of 150 kPa, oleic acid flow rate equal to 1.3 g/min using 0.7% sulfuric acid (mol of sulfuric acid/mol of oleic acid), and 2 h of reaction time. The simulations showed that esterification is governed by temperature, but it is possible to observe that the atomization pressure affects more conversion of oleic acid under a low temperature (<323 K).
1 January 2021 in Anais da Academia Brasileira de Ciências
The understanding of the mechanisms that affect oil production in carbonaceous reservoirs has become increasingly necessary, particularly in limestone, which mostly features oil wettability properties that diminishes petroleum recovery. The objective of this work was to investigate the ability of anionic surfactant (coconut oil derived soap) to adsorb in limestone in order to promote wettability change. The finite-bath technique was employed with changes in temperature, mass of adsorbent material (limestone), contact time and surfactant concentration. Contact angle and zeta potential measurements were also made. The surfactant could be significantly adsorbed on the rock, possibly due to ions that are charged oppositely to the species on the rock surface. A temperature rise from 30 °C to 50 °C was unfavourable to the adsorption capacity. The oil-wettable in-natura limestone had its wettability reduced after the treatment with surfactant. The zeta potential measurements showed that electrostatic attractions play an important role in the adsorption process.
7 October 2019 in Journal of Dispersion Science and Technology
The aquatic environments can be contaminated by various metal ions, including Fe3+, Pb2+, Cr6+. In order to capture these ions the industry commonly uses different natural adsorbents or chemically treated. Based on this approach, this work aimed to treat diatomite with a micelle solution and microemulsion systems, formulated with UNITOL L-90, n-butanol, kerosene and distilled water. The diatomite treated with micelle solution did not provide a significant improvement in removal efficiency, reaching 62% for Fe3+, 58% for Pb2+ and 47% for Cr6+. While the diatomite treated with microemulsion had a substantial increase in the capture percentage reaching 99% of Fe3+, 65% for Pb2+ and 66% for Cr6+. Therefore, based on the results it is clear that surfactant is incorporated to diatomite when a microemulsion system is applied, enhancing the use of this systems in water treatment process. The ethoxylate groups present in the diatomite modified with the microemulsion were fundamental to improve the adsorption capacity of the Fe3+, Pb2+ and Cr6+ ions.