Gallium nitride (GaN)-based high electron mobility transistors (HEMTs) are essential components in modern radio frequency power amplifiers. In order to improve both the device electrical and thermal performance (e.g., higher current density operation and better heat dissipation), researchers are introducing AlN into the GaN HEMT structure. The knowledge of thermal properties of the constituent layers, substrates, and interfaces is crucial for designing and optimizing GaN HEMTs that incorporate AlN into the device structure as the barrier layer, buffer layer, and/or the substrate material. This study employs a multi-frequency/spot-size time-domain thermoreflectance approach to measure the anisotropic thermal conductivity of (i) AlN and GaN epitaxial films, (ii) AlN and SiC substrates, and (iii) the thermal boundary conductance for GaN/AlN, AlN/SiC, and GaN/SiC interfaces (as a function of temperature) by characterizing GaN-on-SiC, GaN-on-AlN, and AlN-on-SiC epitaxial wafers. The thermal conductivity of both AlN and GaN films exhibits an anisotropy ratio of ∼1.3, where the in-plane thermal conductivity of a ∼1.35 μm thick high quality GaN layer (∼223 W m−1 K−1) is comparable to that of bulk GaN. A ∼1 μm thick AlN film grown by metalorganic chemical vapor deposition possesses a higher thermal conductivity than a thicker (∼1.4 μm) GaN film. The thermal boundary conductance values for a GaN/AlN interface (∼490 MW m-2 K−1) and AlN/SiC interface (∼470 MW m−2 K−1) are found to be higher than that of a GaN/SiC interface (∼305 MW m−2 K−1). This work provides thermophysical property data that are essential for optimizing the thermal design of AlN-incorporated GaN HEMT devices.
AlxGa1−xN with a high Al composition (x) presents significant potential for advancing next-generation high-power electronic devices. To support the thermal design of AlxGa1−xN-based electronics, the thermal conductivity of AlxGa1−xN thin films was measured as a function of Al composition, temperature, and film thickness using time-domain thermoreflectance and frequency-domain thermoreflectance techniques. The measurement results were interpreted by modeling phonon transport in AlxGa1−xN films using the phonon Boltzmann transport equation. Phonon properties, including frequencies, group velocities, and lifetimes, were calculated using a virtual crystal approximation, with the effects of mass-disorder scattering incorporated via the Tamura model. The measured thermal conductivity of Al0.7Ga0.3N is an order of magnitude lower than those for GaN and AlN, exhibits an increase followed by saturation with temperature, and shows a modest decrease with a reduction in the film thickness. The modeling results agree with the measurement results and reveal that mass-disorder scattering and phonon-boundary scattering are the dominant mechanisms that reduce the thermal conductivity of AlxGa1−xN thin films.
4 December 2025 in IEEE Transactions on Electron Devices
This work presents a comprehensive study that systematically optimizes the buffer layer thickness of gallium nitride (GaN) high-electron-mobility transistors (HEMTs) in order to minimize the device thermal resistance (${\textit {R}}_{\text {Th}}$ ). Time-domain thermoreflectance (TDTR) and Callaway’s phonon gas model were used to create a temperature-dependent anisotropic thermal conductivity ($\kappa $ ) dataset of GaN films for a thickness range of 0.2–$2~\mu $ m. Device thermal models that employ the $\kappa $ data and the measured thermal boundary resistance (TBR) at the GaN/SiC interface were created and validated using Raman thermometry. The models were used to perform thermal optimization of the GaN buffer thickness. For a TBR of ~3 m${}^{{2}}~\cdot $ K/GW and fully open channel operation, reducing the buffer thickness from 2 to $0.2~\mu $ m decreases the ${\textit {R}}_{\text {Th}}$ of single-, two-, and six-finger HEMTs by 4.9%–5.1%. However, when the TBR exceeds 6 m${}^{{2}} \cdot $ K/GW, thicker buffers are favorable. The operational bias condition also plays a pivotal role. Under a partially pinched-off condition (for a TBR of ~3 m${}^{{2}} \cdot $ K/GW), a thicker buffer (2 versus $0.2~\mu $ m) reduces the ${\textit {R}}_{\text {Th}}$ by 26%. In addition, $\kappa $ models relying on room-temperature or isotropic values were found to lead to incorrect buffer layer design. These results underscore the importance of incorporating accurate $\kappa $ data, TBR, and operational bias conditions into the GaN buffer design to minimize the ${\textit {R}}_{\text {Th}}$ of GaN HEMTs.
Lead zirconate titanate (PZT) thin films offer advantages in microelectromechanical systems (MEMSs) including large motion, lower drive voltage, and high energy densities. Depending on the application, different substrates are sometimes required. Self-heating occurs in the PZT MEMS due to the energy loss from domain wall motion, which can degrade the device performance and reliability. In this work, the self-heating of PZT thin films on Si and glass and a film released from a substrate were investigated to understand the effect of substrates on the device temperature rise. Nano-particle assisted Raman thermometry was employed to quantify the operational temperature rise of these PZT actuators. The results were validated using a finite element thermal model, where the volumetric heat generation was experimentally determined from the hysteresis loss. While the volumetric heat generation of the PZT films on different substrates was similar, the PZT films on the Si substrate showed a minimal temperature rise due to the effective heat dissipation through the high thermal conductivity substrate. The temperature rise on the released structure is 6.8× higher than that on the glass substrates due to the absence of vertical heat dissipation. The experimental and modeling results show that the thin layer of residual Si remaining after etching plays a crucial role in mitigating the effect of device self-heating. The outcomes of this study suggest that high thermal conductivity passive elastic layers can be used as an effective thermal management solution for PZT-based MEMS actuators.
6 March 2026 in IEEE Transactions on Electron Devices
In this work, the junction-to-heat sink thermal resistance (R${}_{\text {th}}\text {)}$ of single-finger GaN high-electron-mobility transistors (HEMTs) mounted on a high-power laminate CuMo base package was analyzed using micro-Raman thermometry and electrothermal modeling. Analysis of the internal temperature distribution reveals that the die-attach material, substrate, and the semi-insulating buffer layer, respectively, comprise 2%, 28%, and 63% of the total Rth of a packaged device. To reduce the Rth of the device, the use of a high $\boldsymbol {\kappa }$ (22 W/m$\boldsymbol {\cdot } $ K) silver epoxy or AuSn solder (57 W/m$\boldsymbol {\cdot }$ K) as the die-attach material is recommended. Simulation results indicate that replacing the substrate with single-crystal diamond lowers Rth by 21%, compared to a standard GaN-on-SiC HEMT. Regarding buffer engineering, a thinner semi-insulating GaN buffer layer leads to a reduced Rth under a fully open channel bias condition. In contrast, under a partially pinched-off bias condition, reducing the thickness of the buffer layer from $1.8~\boldsymbol {\mu }$ m to 400 nm leads to a ~10% increase in peak channel temperature rise. This finding was confirmed by performing nanoparticle-assisted Raman thermometry on transfer length method (TLM) structures with varying channel lengths, which demonstrated that buffer layer thickness optimization must account for the heat flux distribution and device geometry. Simulation results show that deposition of a polycrystalline (PC) diamond top-side heat spreader can lower Rth of a GaN-on-SiC HEMT by 17%. The findings of this work provide insight into the thermal design optimization of GaN monolithic microwave integrated circuits (MMICs).