1 October 2021 in IEEE Transactions on Electron Devices
A narrow coupling ladder-type extended interaction klystron (EIK) operating at 0.34 THz is proposed and analyzed. Compared with the traditional THz EIKs, the narrow coupling EIK can offer higher power capability and increased efficiency because such arrangement has higher characteristic impedance and a more uniform electric field in the beam tunnel. This article studies the electric field distribution of the narrow coupling circuits and traditional circuits. Moreover, the coefficient of variation is introduced to quantify the uniformity of the axial electric field in the beam tunnel. The operating stability is also ensured by adjusting the period length and number of cells. The 3-D particle-in-cell (PIC) simulation predicts the ideal EIK, driven by a 0.15-A, 17.5-kV electron beam confined in a 0.22-mm diameter beam tunnel, and generates an output power of 41 W. The corresponding gain, electronic efficiency, and 3-dB bandwidth are 28.03 dB, 1.56%, and 600 MHz, respectively. Finally, in order to verify the feasibility of the designed structure, we perform a sensitivity study on the EIK design for an eight-micron fabrication tolerance assuming normal distributions for all critical dimensions per each cell with PIC simulations.
14 February 2022 in IEEE Transactions on Electron Devices
The design approaches of the overlapping-mode extended interaction klystrons (EIKs) are presented to satisfy the requirement for broadband terahertz power amplifiers. Since all the cavities are designed and tuned to operate in multiple-cavity modes, the overlapping-mode EIKs can provide high output power over a wider frequency band. The circuit characteristics of the overlapping-mode EIKs are studied, including the dispersion curve, the coupling coefficient, and the frequency interval between cavity modes. Moreover, a six-cavity EIK operating at 0.34 THz is designed to demonstrate the broadband output capability of the overlapping-mode EIKs. The $2\pi $ -mode and its adjacent axial mode, the $\pi $ /13-mode, are chosen as the operating modes of the designed EIK. The 3-D particle-in-cell (PIC) simulation predicts a 3-dB bandwidth of 2.9 GHz for the designed power amplifier at a small-signal level or in saturation. Driven by an input power of 10 mW, the amplifier can provide the output power of 3.9 W, and the corresponding gain is 25.9 dB. When the input power is 150 mW, the amplifier is partially saturated and can provide the output power of 33 W with a corresponding electronic efficiency of 1.23%.
22 April 2020 in IEEE Transactions on Plasma Science
The stable operation of the high-order mode multibeam extended-interaction oscillator (EIO) with coaxial structure can effectively overcome the size limitation of the fundamental mode operating circuit at high frequency. The research on the transverse mode shows that the high-order TM₃₁ mode can establish a stronger axial electric field than the fundamental TM₀₁ mode in a large size coaxial cavity. Although the design of a coaxial extended interaction cavity is straightforward, the operating stability is greatly affected by the mode competition. Based on the interaction characteristic between the multiple beams and the multigap cavity operating in the high-order mode, this article proposes a simplified analysis method based on the equivalent circuit theory to study the high-frequency characteristics of the complex structure. The space-charge wave theory is combined with the dispersion curve to analyze the stability of the five-gap coaxial EIO operating in the TM₃₁ mode. Finally, the particle-in-cell (PIC) simulation has obtained a TM₃₁ mode EIO operating at 35.3 GHz with an output power of 290.3 kW. The device uses six beams with a total current of 25.8 A (evenly divided among six beams) at a voltage of 51 kV. The design provides a promising approach for making a stable high-power RF circuit applied in high-frequency EIOs.
17 March 2022 in IEEE Transactions on Electron Devices
The efficiency of the RF power sources is one of the major concerns in the large-scale high-energy accelerator projects such as the future circular collider (FCC) and the compact linear collider (CLIC). The new bunching method, the core stabilization method (CSM), can achieve high efficiency in the case of shorter interactive length. The multibeam klystron (MBK) could accommodate high RF power with a low operating voltage, compared with a single-beam klystron. This article presents the design and simulation of a 650-MHz, 0.9-MW continuous wave (CW) CSM MBK. The detailed design of a six-beam optics system is also elaborated in this article. The performance of such a device was validated by the 3-D particle-in-cell (PIC)-code computer simulation. With an operating voltage of 50 kV, PIC simulation predicts an efficiency of 81.8%.
29 December 2020 in IEEE Transactions on Electron Devices
A dual-mode five-beam extended interaction klystron (EIK) with a coaxial structure is proposed that can stably obtain high output power. The TM_mn mode with uniform angular distribution in the coaxial cavity can effectively interact with beams located at the peaks of the axial electric field. However, when the center radius of the cavity is enlarged to meet the cathode area requirements of high-power devices at high frequency, the interval between adjacent modes will rapidly decrease. Especially when combined with a multigap structure, the circuit will suffer from mode competition. This article describes a study of the beam-wave interaction characteristics of the multigap coaxial cavity driven by multiple beams, contributing to a stable circuit design. The results show that the appropriate mode selection for each cavity can increase the stability and efficiency of this device. A Ka-band EIK with four cavities has been designed to show the circuit capability. The output cavity operates in the TM₅₁-2π mode, but the other cavities operate in the TM₀₁-2π mode. The 3-D particle-in-cell (PIC) simulation predicts a power of 211.6 kW at 35.19 GHz with the beam parameters of a voltage of 42 kV and a total current of 15 A (3 A x 5). The corresponding gain, electronic efficiency, and 3-dB bandwidth are 53.26 dB, 33.5%, and 50 MHz.
25 March 2022 in IEEE Transactions on Electron Devices
In this article, the design study of a V-band klystron with an internal coupling cavity is presented. The effective characteristic impedance of the internal coupling cavity is approximately 25% higher than that of the external coupling cavity when both operate at $\pi $ mode. A V-band RF circuit of 35% efficiency has been designed based on the proposed internal coupling cavity. An RF circuit based on single-gap resonators was designed first with the help of genetic algorithms (GAs). Then, a five-gap internal coupling cavity replaced the last several resonators to improve circuit bandwidth and efficiency. Simulation results have shown that the proposed internal coupling cavity can significantly improve the efficiency and bandwidth of an RF circuit based on single-gap resonators. Driven by a 60-kV and 9-A pencil beam, the designed RF circuit can achieve a peak power of 188.5 kW, a gain of 47.8 dB, and a 1-dB bandwidth of 180 MHz. The matching high compression ratio beam optics is also elaborated in this article.