1 September 2015 in Colloids and Surfaces A: Physicochemical and Engineering Aspects
10 January 1995 in Journal of Fluid Mechanics
Care is needed with algorithms for computer simulations of the Brownian motion of complex systems, such as colloidal and macromolecular systems which have internal degrees of freedom describing changes in configuration. Problems can arise when the diffusivity or the inertia changes with the configuration of the system. There are some problems in replacing very stiff bonds by rigid constraints. These problems and their resolution are illustrated by some artificial models; firstly in one dimension, then in the neighbourhood of an ellipse in two dimensions and finally for the trimer polymer molecule.
10 February 1996 in Journal of Fluid Mechanics
Numerical simulations are employed to study the Brownian motion of a bead-rod polymer chain dissolved in a solvent. An investigation is conducted of the relaxation of the stress for an initially straight chain as it begins to coil.For a numerical time step δt in the simulations, conventional formulae for the stress involve averaging large ±O(1/(δt)1/2) contributions over many realizations, in order to yield an O(1) average. An alternative formula for the stress is derived which only contains O(1) contributions, thereby improving the quality of the statistics.For a chain consisting of n rods in a solvent at temperature T, the component of the bulk stress along the initial chain direction arising from tensions in the rods at the initial instant is . The dominant physical processes occurring in these separate short, long and intermediate time regimes are identified.
1 January 2016 in Journal of Colloid and Interface Science
The relative immobility of foam in porous media suppresses the formation of fingers during oil displacement leading to a more stable displacement which is desired in various processes such as Enhanced Oil Recovery (EOR) or soil remediation practices. Various parameters may influence the efficiency of foam-assisted oil displacement such as properties of oil, the permeability and heterogeneity of the porous medium and physical and chemical characteristics of foam. In the present work, we have conducted a comprehensive series of experiments using customised Hele-Shaw cells filled with either water or oil to describe the effects of foam quality, permeability of the cell as well as the injection rate on the apparent viscosity of foam which is required to investigate foam displacement. Our results reveal the significant impact of foam texture and bubble size on the foam apparent viscosity. Foams with smaller bubble sizes have a higher apparent viscosity. This statement only applies (strictly speaking) when the foam quality is constant. However, wet foams with smaller bubbles may have lower apparent viscosity compared to dry foams with larger bubbles. Furthermore, our results show the occurrence of more stable foam-water fronts as foam quality decreases. Besides, the complexity of oil displacement by foam as well as its destabilizing effects on foam displacement has been discussed. Our results extend the physical understanding of foam-assisted liquid displacement in Hele-Shaw cell which is a step towards understanding the foam flow behaviour in more complex systems such as porous media.
1 March 2017 in Journal of Colloid and Interface Science
Foams demonstrate great potential for displacing fluids in porous media which is applicable to a variety of subsurface operations such as the enhanced oil recovery and soil remediation. The application of foam in these processes is due to its unique ability to reduce gas mobility by increasing its effective viscosity and to divert gas to un-swept low permeability zones in porous media. The presence of oil in porous media is detrimental to the stability of foams which can influence its success as a displacing fluid. In the present work, we have conducted a systematic series of experiments using a well-characterised porous medium manufactured by 3D printing technique to evaluate the influence of oil on the dynamics of foam displacement under different boundary conditions. The effects of the type of oil, foam quality and foam flow rate were investigated. Our results reveal that generation of stable foam is delayed in the presence of light oil in the porous medium compared to heavy oil. Additionally, it was observed that the dynamics of oil entrapment was dictated by the stability of foam in the presence of oil. Furthermore, foams with high gas fraction appeared to be less stable in the presence of oil lowering its recovery efficiency. Pore-scale inspection of foam-oil dynamics during displacement revealed formation of a less stable front as the foam quality increased, leading to less oil recovery. This study extends the physical understanding of oil displacement by foam in porous media and provides new physical insights regarding the parameters influencing this process.