Jingtao Huang

Jingtao Huang

Auto-generated profile, based on publicly available information

Jingtao Huang

College of Electrical Engineering, Sichuan University, Chengdu, China

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 March 2023 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
ZTZhirong Tang
Zhirong Tang
YXYefei Xu
Yefei Xu
KZKai Zhou
Kai Zhou
PMPengfei Meng
Pengfei Meng
JHJingtao Huang
Jingtao Huang
ZLZhongying Liang
Zhongying Liang
Due to the spurious peaks caused by multi-reflection and the randomness of the cable transfer function, the frequency domain reflection (FDR) method based on Fourier transform (FT) is inaccurate, even resulting in misjudging the soft faults of the cable. Thus, in this paper, a frequency sweep location method based on multiple signal classification (MUSIC) pseudospectrum is proposed to accurately diagnose and locate the soft faults. The idea of the method is to extend the cable transfer function into an array signal and estimate the MUSIC-pseudospectrum of the transfer function, which can transform the analysis of uncertain signals into the analysis of deterministic functions. Thus, the impact of the spurious peaks and the randomness of the cable transfer function can be eliminated. First, the transfer function of the cable is obtained by frequency sweep. Then the soft fault information in the transfer function is extracted and reconstructed by variational mode decomposition (VMD), which has a good ability to divide the harmonic frequency band. The MUSIC-pseudospectrum of the reconstructed signal is estimated to locate the cable soft faults. At last, the feasibility and effectiveness of the proposed method were verified by testing on a laboratory cable and field underground cable.

1 May 2023 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
JHJingtao Huang
Jingtao Huang
KZKai Zhou
Kai Zhou
YXYefei Xu
Yefei Xu
PMPengfei Meng
Pengfei Meng
ZTZhirong Tang
Zhirong Tang
ZLZhongying Liang
Zhongying Liang
A frequency domain reflection (FDR) method has been widely used to locate cable defects. Generally, the performance of the FDR method can be enhanced by extending the sweeping frequency range of the signal. However, with the increase in the signal frequency, misdiagnosis can easily occur owing to the attenuation of the signal and noise. Thus, this paper’s authors propose the upper sweeping frequency (UF) selection method of FDR to improve the accuracy of cable defect location. First, the cable’s three-dimensional location spectrum, including the frequency and spatial information, is obtained at a wide frequency range based on short-time Fourier transform with excellent time-frequency aggregation characteristics. Second, the reasonable UF is selected through the energy change characteristics of the cable end. Then, the optimal localization result of the cable defect is calculated by interpolating the sum of energy among the effective frequency bands. Finally, two single-and multi-defect cases are used for the YJV-8.7/10kV XLPE power cable in the experiment to demonstrate the performance of the proposed method. The experimental results show that with the UF selection method, the impact of high-frequency signal attenuation on defect location is eliminated, and cable defect can be localized with more accuracy.

19 October 2023 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
KZKai Zhou
Kai Zhou
ZTZhirong Tang
Zhirong Tang
PMPengfei Meng
Pengfei Meng
JHJingtao Huang
Jingtao Huang
YXYefei Xu
Yefei Xu
XRXianjie Rao
Xianjie Rao
The phase of the reflected wave at the defect can characterize the change type of the defect. The frequency domain reflection (FDR) method can be used to locate cable defects based on the frequency from reflected waves, but cannot determine the sign of a reflected wave. In this article, a sign judgment method for the reflection wave at the defect is proposed to analyze the change type of the defect. First, the fast Fourier transform (FFT) interpolation algorithm of the Hanning self-convolution window is used to analyze the phase of the reflected wave. Then, the phase deviations are corrected to eliminate the effect of the limited starting frequency of the FDR method. Also, the frequency-dependent wave velocity is revised according to the defect location. The frequency value and the corrected phase value are used to obtain the propagation distance and the sign of the reflected wave, respectively. And the feasibility of the proposed method is analyzed based on the simulated cable models with single reflection wave and multireflection waves. Finally, the effectiveness and accuracy of the proposed method are verified through experiments on a 105 m 10 kV cross-linked polyethylene cable and a 10 kV distribution cable with a length of 1335.3 m.

18 September 2024 in IEEE Transactions on Dielectrics and Electrical Insulation
Verified
Journal Article
Closed access
JHJingtao Huang
Jingtao Huang
KZKai Zhou
Kai Zhou
QZQi Zhao
Qi Zhao
YXYefei Xu
Yefei Xu
PMPengfei Meng
Pengfei Meng
SLSiyan Lin
Siyan Lin
To identify and localize buffer layer moisture defects in high-voltage (HV) cables, this paper verifies the effectiveness of the Frequency Domain Reflectometry (FDR) method theoretically and experimentally by analyzing the impact of moisture on the characteristic impedance of the cable. The article first analyzes the relationship between the electrical parameters of the buffer layer and the characteristic impedance of the cable. Subsequently, the electrical parameters were tested for buffer layer samples at different degrees of moisture, and the characteristic impedance of the cable was calculated. The results indicate that the characteristic impedance of the cable decreases after moisture exposure primarily due to a significant increase in the dielectric constant of the buffer layer. As the degree of moisture increases, the characteristic impedance gradually decreases until it becomes stable. This is mainly due to its rate of change being inversely related to the square of the dielectric constant of the buffer layer. This provides a theoretical basis for the implementation of the FDR method. Finally, this paper conducted FDR tests on HV cables with different degrees of moisture, demonstrating that the FDR method can effectively locate buffer layer moisture defects.

1 April 2026 in High Voltage
Verified
Journal Article
Open access
PDF file
JHJingtao Huang
Jingtao Huang
KZKai Zhou
Kai Zhou
YXYefei Xu
Yefei Xu
ZTZhirong Tang
Zhirong Tang
ZTZuoxin Tang
Zuoxin Tang
XRXianjie Rao
Xianjie Rao
A time domain pulse (TDP) based on the frequency domain reflectometry (FDR) method can be used to diagnose the insulation state of cable defects. However, because of the limitations of the FDR test instrument, the lack of a reflection coefficient spectrum (RCS) in the low‐frequency band (LFB) can result in low frequency oscillation in the time domain reflection signal, which may shield the TDP characteristics of cable defects and then affect the diagnosis of the insulation state of the local defect. To improve the diagnostic performance of the insulation status of local defects in power cables, a low‐frequency stitching technology based on time domain reflectometry (TDR) and FDR is proposed in this work. First, the influence of the RCS in the LFB on the TDP characteristic is analysed through different lower frequency limits. Then, the principles of the proposed low‐frequency stitching technology are introduced in detail, including headend impedance mismatch compensation and the low frequency stitching algorithm. Finally, through simulation and an actual test of two power cables, the effectiveness of the proposed method is verified. The experimental results showed that using the low frequency stitching method could effectively obtain the RCS in the LFB, suppress low‐frequency oscillations in the time domain reflection signal and further enhance the TDP characteristics of the cable defects. Thus, the diagnostic performance of the insulation state of the defect could be improved.