1 January 2018 in Advances in Materials Science and Engineering
This paper presents the experimental testing and simulation results of ballistic impact tests on laminated armor samples that consist of three layers of different materials: fiber‐cement, Kevlar fabric, and steel. In experimental tests, a 9 mm FMJ bullet was launched towards a 100 cm2 sample of the armor from the fiber‐cement side. Ansys Workbench Explicit Dynamics and Ansys AUTODYN 3D were used to model and simulate the ballistic impact. Experimental testing and simulation results were compared to analyze the behavior of composite armor designs, and a good agreement was observed.
1 October 2017 in International Journal of Hydrogen Energy
28 January 2018 in Advances in Materials Science and Engineering
This present study was carried out to check the feasibility of different cellulose fibers obtained from cropped virgin cellulose, blenched eucalyptus, and araucaria pulps through different new environmentally friendly curing processes for fiber‐cement production. The aim is to introduce the different sources of cellulose fibers with lower cost to produce the “fiber‐cement without autoclave” (FCWA). The slurries used in the experiments contain approximately 8% wt. of cellulose. The influence of the waste marble powder addition to the cement mixture was also studied. The physical and mechanical properties of the products which were prepared with this method under different curing conditions were investigated. The mechanical properties of eucalyptus cellulose appear to offer the best combination, especially after longer air‐cure cycles. The results showed that the production of FCWA is very economical by using waste marble powders. And moreover, two new types of cellulose fibers (eucalyptus and araucaria celluloses; EuC and ArC, resp.), which provide a better density and packing in the fiber‐cement leading to better modulus of rupture (MOR) and modulus of elasticity (MOE) values as virgin cellulose (ViC), are very usable for production of the fiber‐cement in industrial scale.
11 September 2018 in Ceramics International
3 October 2017 in Journal of Chemistry
This work presents a different approach to preparing polymer electrolytes having borate ester groups for lithium ion batteries. The polymers were synthesized by reaction between poly(ethylene glycol) methyl ether (PEGME) and BH3-THF complex. Molecular weight of PEGMEs was changed with different chain lengths. Then the polymer electrolytes comprising boron were prepared by doping of the matrices with CF3SO3Li at various molar ratios with respect to EO to Li and they are abbreviated as PEGMEX-B-. The identification of the PEGME-borate esters was carried out by FTIR and 1H NMR spectroscopy. Thermal properties of these electrolytes were investigated via thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The ionic conductivity of these novel polymer electrolytes was studied by dielectric-impedance spectroscopy. Lithium ion conductivity of these electrolytes was changed by the length of PEGME as well as the doping ratios. They exhibit approximate conductivities of 10−4 S·cm−1 at 30°C and 10−3 S·cm−1 at 100°C.
1 March 2019 in Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi
Bu çalışmada, çeşitli stokiyometrik oranlarda hazırlanan nano hekzagonal bor nitrür (NhBN), fosforik asit (FA) ve Nafyon (NAF) içeren yeni nesil proton iletken nano kompozit membran (NKM) üretildi ve su tutma, metanol geçirgenlik ve iyonik iletkenlik değerleri incelendi. NAF ağırlıkça %3-10 oranlarında NhBN ve molce %10-20 oranlarında FA ile karıştırılarak NKM’lar hazırlandı. Metanol geçirgenliği ve su tutma testleri sonuçlarına göre, hidrofobik NhBN parçacıklarının membranların su tutma ve metanol geçirgenliğini azaltırken FA’in su tutma özelliği ve metanol geçirgenliğini arttırdığı gözlemlendi. Maksimum proton iletkenliği, nem içermeyen ortamda 150°C'de, molce %20 FA ve ağırlıkça %3 NhBN içeren NKM için 0.056 S/cm olarak ölçüldü.