Tamara Paludo

Tamara Paludo

Auto-generated profile, based on publicly available information

Tamara Paludo

Department of Restorative Dentistry, PUC - Pontifícia Universidade Católica do Rio Grande do Sul, Porto Alegre, RS, Brazil

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2019 in Brazilian Oral Research
Verified
Journal Article
Open access
PDF file
TPTamara Paludo
Tamara Paludo
MMMaurem Leitão Marcondes
Maurem Leitão Marcondes
ASAndré Arigony Souto
André Arigony Souto
GLGuilherme Carpena Lopes
Guilherme Carpena Lopes
ALAlessandro D Loguercio
Alessandro D Loguercio
ASAna Maria Spohr
Ana Maria Spohr
The aim was to evaluate the effect of 2% grape seed extract (GSE) containing phosphoric acid (PhA) on the bond strength to enamel and dentin. The control group was 37% PhA. The following three PhA formulations with 2% GSE and 20% ethanol were obtained: GSE5 = 5% PhA; GSE10 = 10% PhA; and GSE20 = 20% PhA. The enamel and dentin surfaces of molars were etched with the acid solutions, followed by Scotchbond Multi-Purpose adhesive and composite resin application. The tensile bond strength (TBS) test evaluated the bond to enamel after 24 h, and the microtensile bond strength (μTBS) test evaluated the bond to dentin after 24 h and 12-month water storage. Etched enamel and dentin were observed by scanning electron microscopy (SEM) and atomic force microscopy (AFM), respectively. The TBS data were submitted to one-way ANOVA, while µTBS data were submitted to two-way ANOVA and Tukey’s test (α = 0.05). The TBS (MPa) to enamel did not significantly differ among the control (48.1 ± 15.7), GSE5 (46.1 ± 9.6), GSE10 (49.8 ± 13.6) and GSE20 (44.1 ± 11.9) groups (p = 0.537). The µTBS (MPa) to dentin of the control (28.4 ± 14.4) and GSE20 (24.1 ± 8.1) groups were significantly higher than those of the GSE5 (16.8 ± 7.4) and GSE10 (17.5 ± 6.6) groups at 24 h (p < 0.006). After 12-month storage, only GSE5 (21.0 ± 7.8) and GSE10 (17.6 ± 8.0) did not show significantly decreased μTBS (p > 0.145). SEM micrographs showed a shallower enamel etching pattern for GSE5. AFM images showed the formation of collagenous globular structures for GSE5 and GSE10. The different acid solutions did not influence the TBS to enamel, and the µTBS to dentin was stable over time when dentin was etched with GSE5 and GSE10.

1 April 2020 in Brazilian Dental Journal
Verified
Journal Article
Open access
PDF file
FMFernanda Borguetti Manfroi
Fernanda Borguetti Manfroi
EEEduardo Miranda Ethur
Eduardo Miranda Ethur
DSDeise Caren Somacal
Deise Caren Somacal
TPTamara Paludo
Tamara Paludo
ASAna Maria Spohr
Ana Maria Spohr
The aim was to evaluate, in vitro, the influence of pH cycling on microtensile bond strength (µTBS) and percentage of nanoleakage (%NL) in the dentin-adhesive interface. Flat dentin surfaces were obtained in 56 extracted third molars. The teeth were randomly divided into four groups (n=14): G1- Single Bond Universal (etch-and-rinse mode); G2- Single Bond Universal (self-etch mode); G3- Scotchbond Multi-Purpose; G4- Clearfil SE Bond. A block of composite was built on the adhesive area. Eight tooth/resin sets were cut parallel to the tooth’s long axis to obtain 48 beams (0.8 mm2) for each group. Half of the beams were submitted to four cycles of pH cycling (demineralizing solution for 6 h and remineralizing solution for 18 h). The samples were submitted to µTBS test in a universal testing machine. Six tooth/resin sets were cut parallel to the tooth’s long axis to obtain three slices of the central region (1.0 mm thickness). Half of the slices were submitted to pH cycling. The nanoleakage methodology was applied to obtain the %NL at the adhesive interfaces. According to two-way ANOVA, the interaction between factors (adhesive system x storage) was significant (p=0.0001) for µTBS and %NL. After pH cycling, there was a significant decrease in µTBS and a significant increase in %NL for all adhesives. The adhesives applied in the self-etch mode obtained lower %NL, differing significantly from the etch-and-rinse adhesives. It was concluded that the pH cycling negatively influenced the µTBS and %NL for all adhesives evaluated. However, self-etch adhesives allowed less %NL.