A series of imidazolium-based ionic liquids (ILs) were synthesised and used as single component and metal-free homogeneous catalysts to convert a renewable, inexpensive and non-toxic CO2 feedstock into useful products. The cycloaddition of carbon dioxide to epoxides to produce cyclic carbonate was evaluated. A detailed investigation was carried out on a variety of factors that affected the reactivity and selectivity, such as the catalyst structures (nature of cation and anion). The effect of reaction parameters (temperature, reaction time, CO2 uptake and catalyst amount) on the catalytic performance was also investigated in detail. High conversions and selectivities could be achieved under mild pressure condition (5 bar) using 1-n-butyl-3-methylimidazolium bromide. A synergetic effect of the acidic and basic sites as well as suitable hydrogen-bonding strength is considered crucial for the reaction to proceed smoothly. This protocol was found to be applicable to a disubstituted epoxide. Furthermore, the straightforward synthesis of cyclic carbonates by direct oxidative carboxylation from olefins was achieved using only 1-n-butyl-3-methylimidazolium bromide as a catalyst.
A simple and efficient procedure for the synthesis of a new class of selenoesters 4a and 4b was developed. Polarized-light optical microscopy (POM), differential scanning calorimetry (DSC), and X-ray diffraction showed that the selenoester 4a with a shorter alkyl chain displayed a wide nematic range (ΔT = 110.7 °C), while 4b with a longer alkyl chain possesses a rich phase polymorphism: Cr → SmI → SmC → N → I mesophase sequence during heating cycle and I → N → SmC → SmI → SmX → Cr transition on cooling. For 4b, a large temperature range (135.7 °C) from crystal to isotropic phase can be observed. In addition, UV-Vis, steady-state fluorescence emission and excitation spectra in solution were also applied in order to characterize their photophysical behaviour. Compounds 4a and 4b are fluorescent in the blue region and present a Stokes shift at around 80 nm and 39 nm in dichloromethane and dioxane, respectively.
Molecular dynamics simulation has been employed in the computation of the free energy of solvation for a large number of solute molecules with different chemical functionalities in the solvents water, acetonitril, dimethyl sulfoxide, tetrahydrofuran, and carbon disulfide. The free solvation energy has been separated into three contributions: the work necessary to create a cavity around the solute in the solvent, the electrostatic contribution, and the free energy containing the short-range interactions between solute and solvent molecules. The cavitational contribution was computed from the Claverie-Pierotti model applied to excluded volumes obtained from nearest-neighbor solute-solvent configurations treating the solvent molecules as spherical. The electrostatic term was calculated from a dielectric continuum approach with explicitly incorporating the solvent's partial charges. The short-range contribution to the free solvation energy was obtained from the force field employed in the simulations. For solutions with available experimental data for the free energy of solvation, we found a satisfactory agreement of the computed free solvation energies and the experimental data set.
Bis-arylsulfenyl- and bis-arylselanyl-benzo-2,1,3-thiadiazoles were synthesized in good yields by copper-catalysed cross-coupling reaction of arylthiols or diaryl diselenides with the commercially available 4,7-dibromobenzo[c][1,2,5]thiadiazole. The arylsulfenyl derivatives present absorptions in the visible region (∼420 nm) with molar absorptivity coefficient and radiative rate constant values ascribed to spin and symmetry allowed π–π* electronic transitions, with almost complete absence of solvatochromic effect. An emission located in the cyan green to green region (514–570 nm), with a large Stokes shift (90–146 nm) was observed, probably associated to the charge transfer character of the S1 state. Theoretical calculations were also performed in order to study the geometry, charge distribution and photophysical properties of the molecules in their ground and excited electronic states. TD-DFT calculations were performed using the PBE1PBE and CAM-B3LYP functionals with cc-pVDZ basis set for geometrical optimisations in the S0 and S1 states and jun-cc-pVTZ basis set to obtain vertical transition energies and electronic properties. Solvent effects were included by IEF-PCM formalism using solvents with different dielectric constants. The computationally predicted transition energies calculated with CAM-B3LYP are in good agreement with the experimental results. No substantial solvatochromic effect was found in the absorption maxima, but in the emission from S1 state a redshift was observed on increasing the solvent polarity. This fact, combined with higher dipole moment in the first excited state and some spatial separation of HOMO and LUMO orbitals could indicate an intramolecular charge transfer character of the S1 state.