25 September 2020 in IEEE Robotics and Automation Letters
We present an approach for safe, and object-independent human-to-robot handovers using real time robotic vision, and manipulation. We aim for general applicability with a generic object detector, a fast grasp selection algorithm, and by using a single gripper-mounted RGB-D camera, hence not relying on external sensors. The robot is controlled via visual servoing towards the object of interest. Putting a high emphasis on safety, we use two perception modules: human body part segmentation, and hand/finger segmentation. Pixels that are deemed to belong to the human are filtered out from candidate grasp poses, hence ensuring that the robot safely picks the object without colliding with the human partner. The grasp selection, and perception modules run concurrently in real-time, which allows monitoring of the progress. In experiments with 13 objects, the robot was able to successfully take the object from the human in 81.9% of the trials.
25 May 2021 in Sports Biomechanics
The study objective is to test general- and sport-specific adaption during a single training on the Flexibility Trainer. The device is designed to trigger residual muscle tone decreases of the hip-joint muscles by providing (nearly) isokinetic resistance during a full range of motion strength training in adduction/abduction and flexion/extension direction. Static hip flexion and abduction as well as kinematics of double side kicks were analysed on 15 participants before and after training (or rest for controls) to assess general flexibility and sport-specific movement range. Tests were recorded by a Vicon® motion capturing system. Static hip flexion and abduction as well as leg vector spreading angles (VSA) at different nodes of the kick were selected to determine adaptions of active and passive flexibility. Normalised hip joint moments, movement velocities and VSA were calculated to evaluate the training with the device. ANOVAs with 4-repeated measures and Friedman tests were performed to identify time differences and Bonferroni post-hoc test to identify between-subject effects. Significant differences were found for both static flexibility tests (Flexion = 13.65%; Abduction = 9.94%) and the VSA at specific action phases (≤15.15%). Results indicate that short-term adaptions when training with the Flexibility Trainer are exceeding comparable literature showing improved flexibility and sport-specific performance.
1 May 2020 in Proceedings of the Design Society: DESIGN Conference
The belt units of an omnidirectional treadmill need to be connected for a continuous rotational transmission with variating axes angle. Torus gearing is not appropriate due to kinematic reasons, therefore a crown gearing with cone-shaped teeth is proposed. Parameter analysis on a virtual kinematics model show that depending on the cone angle, overlaps occur at different axis angles. Consequently, the shape of the teeth is modified with tip and foot relief and optimized so that no overlapping of the teeth occurs while a large path of contact is provided.
6 November 2020 in Forschung im Ingenieurwesen
Zusammenfassung: Permanenterregte Axialflussmaschinen weisen gegenüber Radialflussmaschinen Vorteile bezüglich der möglichen Abmessungen auf. Bis jetzt wurden vor allem Axialflussmaschinen mit einer vollen Rotorscheibe untersucht. Aufgrund von besseren magnetischen Eigenschaften sind Rotoren aus geschichtetem Elektroblech hergestellt. Radial ausgerichtet führt das zu hohen Kosten, die durch Wicklung des Elektroblechs bei denselben Eigenschaften wesentlich reduziert werden sollen. Die naive numerische Untersuchung mittels FEM scheitert an der großen Anzahl an Kontaktflächen und noch unbekanntem Einfluss der Vorspannung.Um die mechanische Vorauslegung und Nachrechnung zu ermöglichen werden hier Methoden und Vereinfachungen diskutiert, um Aussagen zur Realisierbarkeit zu erhalten. Es wird das aufgewickelte Blech nicht als archimedische Spirale gerechnet, sondern als Blechringe, die auf die Abtriebswelle aufgezogen werden. Die Abmessungen sind im Vorhinein nur teilweise bekannt und dementsprechend werden mögliche Näherungen angeführt.Zur Bewertung der Beanspruchung werden vorerst die Vorspannungen bei unendlich dünnem Elektroblech bestimmt und die Anwendbarkeit und Genauigkeit der Gleichungen bei endlich dünnem Elektroblech festgestellt.Durch diese Vorgehensweise vereinfacht sich die Berechnung erheblich und es kann während der Konstruktion auf die auftretenden Belastungen reagiert werden.