Bo Tang

Bo Tang

Auto-generated profile, based on publicly available information

Bo Tang

Faculty of Mechanical Engineering & Automation, Zhejiang Sci-Tech University, Hangzhou, China

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 August 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
WLWenqi Lu
Wenqi Lu
BTBo Tang
Bo Tang
KJKehui Ji
Kehui Ji
Kaiyuan LuKaiyuan Lu
Kaiyuan Lu
DWDong Wang
Dong Wang
ZYZhijun Yu
Zhijun Yu
The effective identification of the load torque is one of the key methods to improve the positioning accuracy of the position servo system, and the sliding mode observer (SMO) is a common identification method in the speed control system because of its advantages of insensitive parameters and easy physical realisation. However, the existing SMO can not achieve high precision and high response identification of load torque in the full speed range when the motor is running at variable-speed or variable-load, which limits its application in the position servo system. Based on the analysis of the stability and the adaptive law of feedback gain coefficient, an improved SMO for adaptive identification based on adaptive control and improvement of cut-off frequency is proposed. To verify the proposed method, the dedicated simulation model and test platform are built. The results show that the proposed observer can realise the adaptive identification of the load torque under the condition of variable-speed or variable-load, and the estimation accuracy is high. The position servo system designed by the proposed observer can improve the response against load change, which is an effective method for high-precision positioning control of the position servo system with a variable-speed or variable-load.

29 December 2021 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
BTBo Tang
Bo Tang
WLWenqi Lu
Wenqi Lu
Bo YanBo Yan
Bo Yan
Kaiyuan LuKaiyuan Lu
Kaiyuan Lu
JFJianchao Feng
Jianchao Feng
LGLiang Guo
Liang Guo
Improving the positioning response is one of the key goals for permanent magnet synchronous motor position servo systems. The sliding mode variable structure controller (SMVSC) is an effective method due to the advantages of strong robustness, fast response, and easy practical implementation. However, the existing SMVSCs have difficulties in optimizing the position tracking response speed and chattering performance at the same time. This article proposes an improved position speed integrated SMVSC (ISMVSC) with a new variable exponential reaching law based on position error and a saturation function, and a speed-limiting method using speed error and trajectory planning. The general design principle is given and various tests are carried out to verify the effectiveness of the proposed method. The experimental results show that compared with traditional methods, the ISMVSC can improve the positioning response speed and reduce chattering problems at the same time; it also exhibits a stronger transient speed-limiting ability. All these advantages make the proposed controller a superior method to achieve high-response positioning control of the servo system that performs point-to-point motion.

22 September 2020 in IEEE/ASME Transactions on Mechatronics
Verified
Journal Article
Closed access
WLWenqi Lu
Wenqi Lu
BTBo Tang
Bo Tang
YWYaxiong Wu
Yaxiong Wu
Kaiyuan LuKaiyuan Lu
Kaiyuan Lu
DWDong Wang
Dong Wang
XWXiufeng Wang
Xiufeng Wang
High precision position detection of joint and status monitoring of speed reduction gearbox (SRG) are two key technologies in the research and development of selective compliant assembly robot arm (SCARA). The existing schemes have some problems, such as the large occupation of space, high cost, complex implementation, lack of status monitoring, etc. Therefore, firstly, in order to get the accurate position information of joint when the SCARA is powered up at the first time, a new combined incremental encoder with unevenly distributed multiple indexing signals and initial position detection method is proposed. Secondly, in order to get the accurate position information and monitor the operation status of the SRG during the positioning operation, a real-time position detection and status monitoring method based on the transmission error using dual incremental encoder is proposed. The general design principle has been given, and various experimental results have confirmed the effectiveness of the proposed solution. The proposed new combined incremental encoder has the advantage of small occupied space, easy realization and low cost. The proposed position detection and status monitoring method not only realizes the high precision detection of the joint position but also provides the key data for the monitoring of the running state of the SRG.