The 15 January 2022 climactic eruption of Hunga volcano, Tonga, produced an explosion in the atmosphere of a size that has not been documented in the modern geophysical record. The event generated a broad range of atmospheric waves observed globally by various ground-based and spaceborne instrumentation networks. Most prominent was the surface-guided Lamb wave (≲0.01 hertz), which we observed propagating for four (plus three antipodal) passages around Earth over 6 days. As measured by the Lamb wave amplitudes, the climactic Hunga explosion was comparable in size to that of the 1883 Krakatau eruption. The Hunga eruption produced remarkable globally detected infrasound (0.01 to 20 hertz), long-range (~10,000 kilometers) audible sound, and ionospheric perturbations. Seismometers worldwide recorded pure seismic and air-to-ground coupled waves. Air-to-sea coupling likely contributed to fast-arriving tsunamis. Here, we highlight exceptional observations of the atmospheric waves.
21 April 2023 in Bulletin of the Seismological Society of America
Earthquake ground motions in the vicinity of receivers couple with the atmosphere to generate pressure perturbations that are detectable by infrasound sensors. These so-called local infrasound signals traverse very short source-to-receiver paths, so that they often exhibit a remarkable correlation with seismic velocity waveforms at collocated seismic stations, and there exists a simple relationship between vertical seismic velocity and pressure time series. This study leverages the large regional network of infrasound sensors in Alaska to examine local infrasound from several light to great Alaska earthquakes. We estimate seismic velocity time series from infrasound pressure records and use these converted infrasound recordings to compute earthquake magnitudes. This technique has potential utility beyond the novelty of recording seismic velocities on pressure sensors. Because local infrasound amplitudes from ground motions are small, it is possible to recover seismic velocities at collocated sites where the broadband seismometers have clipped. Infrasound-derived earthquake magnitudes exhibit good agreement with seismically derived values. This proof-of-concept demonstration of computing seismic magnitudes from infrasound sensors illustrates that infrasound sensors may be utilized as proxy vertical-component seismometers, making a new data set available for existing seismic techniques. Because single-sensor infrasound stations are relatively inexpensive and are becoming ubiquitous, this technique could be used to augment existing regional seismic networks using a readily available sensor platform.
22 February 2023 in Bulletin of the Seismological Society of America
Earthquakes generate infrasound in multiple ways. Acoustic coupling at the surface from vertical seismic velocity, termed local infrasound, is often recorded by infrasound sensors but has seen relatively little study. Over 140 infrasound stations have recently been deployed in Alaska. Most of these stations have single sensors, rather than arrays, and were originally installed as part of the EarthScope Transportable Array. The single sensor nature, paucity of ground‐truth signals, and remoteness makes evaluating their data quality and utility challenging. In addition, despite notable recent advances, infrasound calibration and frequency response evaluation remains challenging, particularly for large networks and retrospective analysis of sensors already installed. Here, we examine local seismoacoustic coupling on colocated seismic and infrasound stations in Alaska. Numerous large earthquakes across the region in recent years generated considerable vertical seismic velocity and local infrasound that were recorded on colocated sensors. We build on previous work and evaluate the full infrasound station frequency response using seismoacoustic coupled waves. By employing targeted signal processing techniques, we show that a single seismometer may be sufficient for characterizing the response of an entire nearby infrasound array. We find that good low frequency (<1 Hz) infrasound station response estimates can be derived from large ( ) earthquakes out to at least 1500 km. High infrasound noise levels at some stations and seismic‐wave energy focused at low frequencies limit our response estimates. The response of multiple stations in Alaska is found to differ considerably from their metadata and are related to improper installation and erroneous metadata. Our method provides a robust way to remotely examine infrasound station frequency response and examine seismoacoustic coupling, which is being increasingly used in airborne infrasound observations, earthquake magnitude estimation, and other applications.
The addition of 108 infrasound sensors—a legacy of the temporary USArray Transportable Array (TA) deployment—to the Alaska regional network provides an unprecedented opportunity to quantify the effects of a diverse set of site conditions on ambient infrasound noise levels. TA station locations were not chosen to optimize infrasound performance, and consequently span a dramatic range of land cover types, from temperate rain forest to exposed tundra. In this study, we compute power spectral densities for 2020 data and compile new ambient infrasound low- and high-noise models for the region. In addition, we compare time series of root-mean-squared (rms) amplitudes with wind data and high-resolution land cover data to derive noise–wind speed relationships for several land cover categories. We observe that noise levels for the network are dominated by wind, and that network noise is generally higher in the winter months when storms are more frequent and the microbarom is more pronounced. Wind direction also exerts control on noise levels, likely as a result of infrasound ports being systematically located on the east side of the station huts. We find that rms amplitudes correlate with site land cover type, and that knowledge of both land cover type and wind speed can help predict infrasound noise levels. Our results show that land cover data can be used to inform infrasound station site selection, and that wind–noise models that incorporate station land cover type are useful tools for understanding general station noise performance.
19 December 2023 in Seismological Research Letters
Developing techniques for improving quality control (QC) schemes to catch seismic and infrasound data defects continues to be an area of active research. Selecting universal thresholds for the automation of data quality (DQ) checks is an efficient way to find QC issues, but these thresholds may not apply well to multiple stations with varying DQ characteristics. In addition, these thresholds may not catch subtle changes in DQ parameters that still indicate problems. Machine learning can be an alternative way of diagnosing QC issues. K-means clustering, an unsupervised machine learning clustering algorithm, has been effectively used in the past for geophysical pattern exploration. This study furthers k-means applications to DQ analysis through clustering on DQ metrics derived from day-long segments of nuclear explosion monitoring data. Our k-means implementation on broadband seismometer DQ metrics separately clustered mass recenters, calibrations lasting at least one hour, and days without either. Applying this technique to infrasound DQ metrics revealed clusters related to physical issues at the stations, such as missing back volume screws and the flooding of ported pipe inlets. These are both examples of QC issues that are difficult to diagnose or detect through the thresholding of metrics or by inspecting waveforms and spectra. Our results show that k-means clustering can be a useful QC tool in exploring DQ patterns to assist analyst review of station operation and maintenance. The learned knowledge from this exploration can then inform a thresholding workflow on how to tailor to individual stations, or the k-means model could classify data directly.