1 January 2018 in Geophysics
We applied the generalized multiscale finite-element method (GMsFEM) to simulate seismic wave propagation in fractured media. Fractures are represented explicitly on a fine-scale triangular mesh, and they are incorporated using the linear-slip model. The motivation for applying GMsFEM is that it can reduce computational costs by using basis functions computed from the fine-scale fracture model to simulate propagation on a coarse grid. First, we apply the method to a simple model that has a uniform distribution of parallel fractures. At low frequencies, the results could be predicted using a homogeneous, effective medium, but at higher frequencies, GMsFEM allows simulation of more complex, scattered wavefields generated by the fractures without assuming a specific form of anisotropy. A second, more complex model has two fracture corridors in addition to a few sparsely distributed fractures. Simulations compare scattered wavefields for different acquisition geometries. The third test case represents a vertical section of subsurface structures and is designed to test the influence of fractures on the surface seismic. We compared the fine-scale solution with multiscale solution to demonstrate the accuracy and efficiency of computations. Given the simulation results of three different test cases, GMsFEM allows a reduction of computation time of approximately 80% compared with a conventional finite-element result computed directly from the fine-scale grid, and it can predict seismic signal variations useful for the interpretation of fracture distributions.
1 October 2021 in Geophysical Journal International
SUMMARY: In an ideal case, the time-lapse differences in 4-D seismic data should only reflect the changes of the subsurface geology. Practically, however, undesirable discrepancies are generated because of various reasons. Therefore, proper time-lapse processing techniques are required to improve the repeatability of time-lapse seismic data and to capture accurate seismic information to analyse target changes. In this study, we propose a machine learning-based time-lapse seismic data processing method improving repeatability. A training data construction method, training strategy and machine learning network architecture based on a convolutional autoencoder are proposed. Uniform manifold approximation and projection are applied to the training and target data to analyse the features corresponding to each data point. When the feature distribution of the training data is different from the target data, we implement data augmentation to enhance the diversity of the training data. The method is verified through numerical experiments using both synthetic and field time-lapse seismic data, and the results are analysed with several methods, including a comparison of repeatability metrics. From the results of the numerical experiments, we can conclude that the proposed convolutional autoencoder can enhance the repeatability of the time-lapse seismic data and increase the accuracy of observed variations in seismic signals generated from target changes.
6 September 2024 in Computers & Geosciences
1 August 2018 in Interpretation
Accurate estimation of subsurface properties plays an important role in successful hydrocarbon exploration, and a variety of different types of inversion schemes are used to infer earth properties such as velocity or density by analyzing the surface seismic. The Markov-chain Monte Carlo (MCMC) stochastic approach is widely used to estimate subsurface properties. We have used a transdimensional form of MCMC, reversible jump MCMC (RJMCMC), to estimate seismic impedance, which allows the inference of the number of interfaces as well as the interface location and layer impedances. Estimating the uncertainty quantitatively is also very important when performing stochastic inversion. Therefore, the goal of this paper is to apply the transdimensional method to obtain a 3D seismic impedance model and to quantify uncertainty in impedance and interface locations. We also measured the speedup of the proposed algorithm by applying data and task parallelism. To demonstrate the performance and reliability of the proposed RJMCMC impedance inversion, we used seismic data from the E-segment of the Norne field in Norwegian Sea. The results of the quasi 3D transdimensional MCMC approach, which independently inverts data from each common-depth-point location, indicate high velocity contrasts near gas-oil contacts and high uncertainty in impedance near discontinuities. Also, the cross section of the impedance uncertainty volume helps to identify the location of a high-contrast boundary corresponding to the location of the possible gas reservoir. The proposed uncertainty measure can serve as an attribute to identify important reservoir features.
23 June 2022 in Geophysics
Estimating porosity models via seismic data is challenging due to the low signal-to-noise ratio and insufficient resolution of the data. Although impedance inversion is often used in combination with well logs, to obtain subseismic scale porosity data, several problems must be addressed. Alternatively, we have proposed a machine learning-based workflow to convert seismic data into porosity models. A residual U-Net++ (ResUNet++)-based workflow is designed to take multiple poststack seismic volumes with different frequency bands as input and estimate a corresponding porosity model as output. This workflow is demonstrated in a 3D channelized reservoir to estimate the porosity model, and the R2 score of more than 0.9 is achieved for training and validation data. Moreover, a stress test is performed by adding noise to the seismic data to verify the expandability of applications, and the results find a robust estimation with 5% added noise. The additional two ResUNet++ are trained to only take the lowest or highest resolution seismic data as input to estimate the porosity model, but they exhibit underfitting and overfitting, respectively, supporting the importance of using multiscale seismic data for the porosity estimation problem. We mainly use experimental cases with simulated data. Therefore, scaling ResUNet++ for real data is needed in future research, such as considering coherent noise in seismic data, allowing uncertainty in petrophysical parameters, and expanding the size of ResUNet++ to the practical reservoir extent.
1 September 2019 in Journal of Marine Systems