12 November 2007 in Applied Physics Letters
The thermal stability of CdZnO∕ZnO multi-quantum-well (MQW) structures was studied using rapid thermal annealing in nitrogen from 300to750°C. Photoluminescence (PL) emission from the MQWs was studied while varying the annealing temperature and time. For 15min annealings, the PL center wavelength showed a 7nm reduction for temperatures up to 650°C. Above 650°C, the wavelength changed rapidly, with a 50nm reduction at 750°C. Annealing at 700°C for up to 20min produced a systematic reduction in PL wavelength up to 39nm. The data suggest that CdZnO∕ZnO MQWs are relatively stable for nitrogen annealing below 650°C for times up to 15min.
17 December 2019 in Journal of Vacuum Science & Technology A
The authors report on high spectral responsivity (SnxGa1 − x)2O3 Schottky UV photodetectors grown by plasma-assisted molecular beam epitaxy on β-Ga2O3 substrates. Schottky devices exhibited peak responsivities ranging from 49 to 194 A/W, with peak responsivity and wavelength position increasing systematically for higher Sn concentration from x = 0.01 to 0.18. Dark currents for the devices ranged from <1 nA to 3 μA with rise and fall times in the 0.21–3 s time range, with slower response times likely due to photoconductive gain caused by trapped holes. Incorporation of up to 18% Sn into the tin gallium oxide (TGO) devices resulted in a redshift in the peak responsivity position, ranging from 5.19 to 4.86 eV, demonstrating tunability within the UV-C spectral region through Sn concentration adjustment. The authors believe this to be the highest reported responsivity for a planar Ga2O3-based Schottky photodetector to date, suggesting that TGO based UV-C Schottky detectors are an attractive approach toward deep-UV sensing applications.
12 September 2022 in Applied Physics Letters
We report ultra-high responsivity of epitaxial (SnxGa1−x)2O3 (TGO) Schottky UV-C photodetectors and experimentally identified the source of gain as deep-level defects, supported by first principles calculations. Epitaxial TGO films were grown by plasma-assisted molecular beam epitaxy on (−201) oriented n-type β-Ga2O3 substrates. Fabricated vertical Schottky devices exhibited peak responsivities as high as 3.5 ×104 A/W at −5 V applied bias under 250 nm illumination with sharp cutoff shorter than 280 nm and fast rise/fall time in milliseconds order. Hyperspectral imaging cathodoluminescence (CL) spectra were examined to find the mid-bandgap defects, the source of this high gain. Irrespective of different tin mole fractions, the TGO epilayer exhibited extra CL peaks at the green band (∼2.20 eV) not seen in β-Ga2O3 along with enhancement of the blue emission-band (∼2.64 eV) and suppression of the UV emission-band. Based on hybrid functional calculations of the optical emission expected for defects involving Sn in β-Ga2O3, VGa–Sn complexes are proposed as potential defect origins of the observed green and blue emission-bands. Such complexes behave as acceptors that can efficiently trap photogenerated holes and are predicted to be predominantly responsible for the ultra-high photoconductive gain in the Sn-alloyed Ga2O3 devices by means of thermionic emission and electron tunneling. Regenerating the VGa–Sn defect complexes by optimizing the growth techniques, we have demonstrated a planar Schottky UV-C photodetector of the highest peak responsivity.
1 October 2007 in Optical Materials
8 December 2020 in Advanced Photonics Research
A high figure‐of‐merit UV‐C solar‐blind photodetector (PD) fabricated from thin‐film beta‐gallium oxide (β‐Ga2O3) grown on n‐Si substrates by plasma‐assisted molecular beam epitaxy is demonstrated. Film growth sequences for nucleation of Ga2O3 on (100)‐ and (111)‐oriented Si substrates are developed, and the influence of crucial growth parameters is systematically investigated, namely, substrate temperature, oxygen flow rate, and plasma power on the functional properties of the PDs. The PDs show an ultra‐high responsivity of 837 A W−1 and a fast ON/OFF time below 4 ms at −5 V. In addition, they display strong rectifying properties and a sharp cutoff below 280 nm with the average responsivities between 10 and 80 A W−1, a detectivity on the order of 1010 Jones, and rise/fall times between 4 and 500 ms. High photoconductive gain is likely to be due to the mid‐bandgap donor/acceptor defect levels, including oxygen vacancies in the form of self‐trapped holes. It is demonstrated that these defect levels can be modified by controlling the growth conditions, thereby allowing for tailoring of the PD characteristics for specific applications. The methodology represents a cost‐effective solution over homoepitaxial approaches, with characteristics that meet or exceed those reported previously, offering new possibilities for on‐wafer integration with Si opto‐electronics.
1 November 1998 in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
Damage introduced from sputtering deposition, electron-beam evaporation, and thermal evaporation were investigated with an InGaAs/GaAs strained quantum well structure. This strained quantum well structure was found to be a more sensitive probe of damage, revealing metallization-induced damage where none was found using comparable lattice-matched quantum wells. The damage was found to vary with deposition method, deposition rates, or even different metal sources used. Noticeable degradation of the photoluminescence of the strained quantum well was observed after a thin layer (∼100 Å) of metal was deposited.