14 August 2020 in Nuclear Fusion
2 February 2021 in Superconductor Science and Technology
Iron-based superconducting (IBS) racetrack coils were firstly fabricated by using 100-m 7-filamentary Ba 1-x K x Fe 2 As 2 (Ba122) tapes at the Institute of High Energy Physics, Chinese Academy of Sciences (IHEP, CAS). The IBS tape was wound in parallel with stainless steel tape to withstand the high tensile hoop stress under high magnetic field. After the heat treatment, the coils were impregnated with epoxy resin. Then the IBS coils were tested in a low-temperature superconducting Common-Coil dipole magnet which provided a maximum background field of 10 T at 4.2 K. Most importantly, the best IBS racetrack coil quenched at 4.2 K and 10 T with an operating current of 65 A, which is still as high as 86.7% of critical current of the short sample at 10 T. The details of the fabrication process and performance test results were presented in this paper. The performance test demonstrated the IBS conductor is a promising candidate for the application of high field magnets especially for future high-energy accelerators.
24 June 2024 in Superconductor Science and Technology
This paper reports an all REBCO (REBa2Cu3Ox, where RE = Y, Gd) superconducting magnet that generated a direct-current magnetic field of 26.86 T at 4.2 K in self-field, which is the highest magnetic field achieved by the high temperature superconducting (HTS) magnet. The magnet consists of a stack of 10 double pancake (DP) coils wound with two different width REBCO conductors, and the no-insulation (NI) winding technology was applied to increase its engineering current density. The inner and outer winding diameters and overall height of the magnet are 30 mm, 103.98 mm, and 102.6 mm, respectively. In order to control the stress risk in HTS magnet, the over-banding made of high elastic modulus stainless steel tapes was employed to the magnet. In addition, no obvious degradation was found in the performance of the magnet after quench at 26.86 T of 295.5 A. These test results demonstrate the great potential of REBCO magnets in high field applications.
30 October 2024 in Superconductor Science and Technology
A higher available magnetic field can provide more flexibility for significant research and construction. Inserting a feasible high-temperature-superconducting (HTS) magnet inside a low-temperature-superconducting (LTS) external is becoming an efficient method to build ultra-high-field (UHF) magnets. However, HTS insert magnets exhibited a concentration of magnetic strain during the energization, significantly owing to the screening-current effect. This phenomenon affects the structural integrity of HTS magnets, posing a difficulty for UHF magnets to reach a center field larger than 30 T. In this paper, we report the recent progress of the 35 T all-superconducting UHF magnet project. The full-cycle development of this homemade UHF magnet was a strong collaboration with multiple domestic institutions in China. We used commercial REBa2Cu3O (RE = rare earth element, REBCO) conductors to wind the 20 T HTS insert. Specifically, we optimized the electromagnetic design of this HTS insert with consideration of screening-current induced strain. We applied the no-insulation and metal-as-insulation winding techniques simultaneously to balance the time constant of the two nested REBCO coils. During the excitation test, the HTS insert maintained a 256 A operation current as designed for nearly 18 h. With the energization of LTS external magnet, the entire facility reached a center field larger than 20 T for 16 h, 30 T for 6.35 h and 32 T for 2 h. It finally reached a 32.4 T center field, at which point the LTS external quenched, inducing the HTS insert to quench as well. After quench, the HTS magnet can maintain 229 A operation current during the postmortem standalone test. This 32.4 T result exhibits the effectiveness of considering the screening-current induced strain to enhance the structural integrity of REBCO magnets, and verifies the high reliability of REBCO magnets by generating a long-duration high field environment without any quench accident originating from the REBCO magnet.
10 October 2022 in Superconductor Science and Technology
The slit technique is an essential process for narrowing the second-generation high-temperature superconducting (2G-HTS) tapes. It is still very challenging to eliminate edge defects introduced during slitting. In this work, we developed a set of reel-to-reel laser slit (LS) equipment for narrowing 2G-HTS tapes using a femtosecond infrared laser. In comparison with the commonly used mechanical slit (MS) technique, the LS technique produced no cracks at the tape edges. Electro-mechanical behaviors of 2G-HTS tapes with MS and LS edges were compared in liquid nitrogen conditions. The results of the uniaxial tensile tests showed only a minor difference in irreversible tensile stress/strain of the two kinds of tapes. However, uniaxial tensile fatigue tests showed that the critical current (I c) retention of the LS tapes was about 14% higher than that of the MS tapes after 104 cycles (@ 77 K, σ max = 0.8σ y, and a stress ratio of 0.1). Moreover, U-Spring compressive tests revealed that no irreversible I c degradation occurred on the LS tapes under compressive strain up to −0.8%, with high reproducibility. On the contrary, the irreversible compressive strains of the MS tapes were rather scattered, ranging from −0.75% to −0.2%. Enhancement of electro-mechanical behaviors is strongly linked to fewer edge defects in the LS tapes. This research demonstrates significant advantages of the LS technique over the conventional MS technique, showing its promising prospects for demanding applications.
1 March 2019 in Superconductor Science and Technology
Iron-based superconductors (IBSs) with ultrahigh upper critical fields and low anisotropies have attracted significant attention in terms of the novel mechanism of superconductivity and high-field applications. A major concern for practical research is the fabrication of long wires with enhanced critical current density and low cost. In this paper, Cu/Ag composited sheathed Ba 0.6 K 0.4 Fe 2 As 2 (Ba122) tapes were fabricated through a hot isostatic pressing method, which is feasible for long-wire manufacturing. The Cu/Ag composite sheath can lower the tape cost by reducing the use of expensive Ag. A high-transport critical current density ( J c ) up to 5.8 × 10 4 A cm −2 under 10 T at 4.2 K was achieved in our tapes. Evidence has shown that these tapes have pure Ba122 phase, homogeneous element distribution, orientated grains and good grain connectivity. Our work shows that low-cost Cu/Ag-sheathed IBS tapes have great promise for practical applications in the future.