Paramedian insertion of orthodontic mini-implants is increasingly used to anchor molar distalizers. The aim of this review was to systematically examine the available measurements of vertical palatal bone height (VBH). PUBMED, MEDLINE and the Cochrane Controlled Trials Register were searched using specific search terms. Hand searches of bibliographies of articles were also performed to identify studies measuring VBH or bone thickness in the human palate. Sixteen studies were included, arising from 19 published articles. Repeat presentations were excluded. Ten of the 11 computed tomogram (CT)-based studies presented data from 956 orthodontic patients on average VBH and its variation at a range of palatal sites. Individual data were not available, and pooling of data was not feasible because of heterogeneity of subjects, different measurement sites, different CT methods and their associated software. The compilation of data did indicate that the region 3–4mm behind the incisive foramen and 3–9mm lateral to the midpalatal suture should normally provide sufficient VBH to anchor molar distalizers. The risks of unwanted effects during distalization should be small, but the limitations listed above and the small numbers of studies available impair the precision of the estimates and do not allow the results to be generalized. Paramedian anchorage in the anterior palate can be recommended for molar distalization but, given the great inter-individual variability of the palatal bone height, it must be preceded by reliable CT-based imaging in patients identified by routine investigations as being at risk.
Introduction: Bone-borne miniscrew assisted palatal expansion (MAPE) is a common technique to improve maxillary transverse deficiency in young adolescents. Adult patients usually present a challenge, as they often require additional surgical assisted maxillary expansion (SARPE). There is still no clear statement about non-surgical expansion in adult patients using this technique. The aim of this study was to evaluate the success and complication rate of non-surgical palatal expansion in adults utilizing MAPE with a novel force-controlled polycyclic expansion protocol (FCPC). Methods: This consecutive study consisted of 33 adult patients with an average age of 29.1 ± 10.2 years (min. 18 years, max. 58 years), including one dropout patient. First, four miniscrews were inserted and after 12-weeks latency, the expander was placed and the FCPC protocol was applied (MAPE group). In case of missing expansion, a SARPE was performed (SARPE group). After maximum expansion, a cone beam CT was made and widening of the midpalatal suture was measured. The outcome variables were successful non-surgical expansion and, with sample size power above 80%, the odds of failed non-surgical expansion and associated complications were evaluated. The primary predictor variable was age. Statistical analysis was performed using R (Version 3.1) to calculate power, to construct various models for measuring the odds of requiring surgical intervention/complications, and others. Results: Successful non-surgical expansion was achieved in 27 patients (84.4%), ranging from 18 to 49 years. Mean age differed significantly between both groups (26.8 ± 8.2 years vs. 41.3 ± 9.9 years; p < 0.001). Mean expansion at the anterior and posterior palate for the MAPE group was 5.4 ± 1.5 mm and 2.5 ± 1.1 mm, respectively. Among these subjects’ complications were observed in 18.5%. Age significantly increased the odds of complications (p = 0.019). Conclusions: 1. The success rate of MAPE among individuals aged 18 to 49 years was 84.4%. 2. A V-shaped expansion pattern in the antero-posterior dimension was mostly observed. 3. Complications were significantly associated with age. 4. A careful expansion protocol seems to be beneficial to prevent unfavorable results in adult patients. Trial registration: Consecutive cohort study, Review Board No. EK-2-2014/0016.
Objectives: Orthodontic mini-implants (OMIs) are increasingly used in orthodontics but can fail for various reasons. This study investigates the effects of OMI design characteristics on the mechanical properties in artificial bone. Material and Methods: Twelve self-drilling OMIs (2 small, 6 medium, 4 large) from 8 manufacturers were tested for their primary stability in simulated medium-high cancellous bone and the risk to fracture in high-density methacrylate blocks. For the assessments of the maximum insertion torque (IT) and torsional fracture (TF) 5 of each OMI were used and for the pull-out strength (POS) 10. The OMIs were inserted with a torque screwdriver (12 sec/360°) until the bottom at 8 mm depth was reached. OMI designs were analyzed with a scan electron microscope (SEM). Results: SEM images revealed a great variation in product refinement. In the whole sample, a cylindrical OMI shape was associated with higher POS (p<0.001) but lower IT (p=0.002) values. The outer and inner OMI diameters were design characteristics well correlated with POS, IT and TF values (ranging from 0.601 to 0.961). Greater thread depth was related to greater POS values (r= 0.628), although OMIs with similar POS values may have different IT values. Thread depth and pitch had some impact on POS. TF depended mainly on the OMI inner (r= 0.961) and outer diameters (r=0.892). A thread depth to outer diameter ratio close to 40% increased TF risk. Conclusions: Although at the same insertion depth the OMI outer and inner diameters are the most important factors for primary stability, other OMI design characteristics (cylindrical vs. conical, thread design) may significantly affect primary stability and torsional fracture. This needs to be considered when selecting the appropriate OMI for the desired orthodontic procedures.
1 March 2009 in Journal of Oral and Maxillofacial Surgery