Bjorn Winther-Jensen

Bjorn Winther-Jensen

Auto-generated profile, based on publicly available information

Bjorn Winther-Jensen

Department of Applied Chemistry and Research Institute for Science and Engineering Waseda University 3-4-1 Okubo, Shinjuku Tokyo 169-8555 Japan

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2008 in Science
Verified
Journal Article
Closed access
PDF file
BWBjorn Winther-Jensen
Bjorn Winther-Jensen
OWOrawan Winther-Jensen
Orawan Winther-Jensen
Maria ForsythMaria Forsyth
Maria Forsyth
DMDouglas R. MacFarlane
Douglas R. MacFarlane
The air electrode, which reduces oxygen (O 2 ), is a critical component in energy generation and storage applications such as fuel cells and metal/air batteries. The highest current densities are achieved with platinum (Pt), but in addition to its cost and scarcity, Pt particles in composite electrodes tend to be inactivated by contact with carbon monoxide (CO) or by agglomeration. We describe an air electrode based on a porous material coated with poly(3,4-ethylenedioxythiophene) (PEDOT), which acts as an O 2 reduction catalyst. Continuous operation for 1500 hours was demonstrated without material degradation or deterioration in performance. O 2 conversion rates were comparable with those of Pt-catalyzed electrodes of the same geometry, and the electrode was not sensitive to CO. Operation was demonstrated as an air electrode and as a dissolved O 2 electrode in aqueous solution.


8 April 2011 in Physical Chemistry Chemical Physics
Verified
Journal Article
Closed access
PDF file
MHMatthias Hilder
Matthias Hilder
BWBjorn Winther-Jensen
Bjorn Winther-Jensen
DLDan Li
Dan Li
Maria ForsythMaria Forsyth
Maria Forsyth
DMDouglas R. MacFarlane
Douglas R. MacFarlane
We describe the direct electro-chemical reduction of graphene oxide to graphene from aqueous suspension by applying reduction voltages exceeding −1.0 to −1.2 V. The conductivity of the deposition medium is of crucial importance and only values between 4–25 mS cm−1 result in deposition. Above 25 mS cm−1 the suspension de-stabilises while conductivities below 4 mS cm−1 do not show a measurable deposition rate. Furthermore, we show that deposition can be carried out over a wide pH region ranging from 1.5 to 12.5. The electro-deposition process is characterised in terms of electro-chemical methods including cyclic voltammetry, quartz crystal microbalance, impedance spectroscopy, constant amperometry and potentiometric titrations, while the deposits are analysed viaRaman spectroscopy, infra-red spectroscopy, X-ray photoelectron spectroscopy and X-ray diffractometry. The determined oxygen contents are similar to those of chemically reduced graphene oxide, and the conductivity of the deposits was found to be ∼20 S cm−1.

10 July 2004 in Macromolecules
Verified
Journal Article
Closed access
BWBjørn Winther-Jensen
Bjørn Winther-Jensen
JCJun Chen
Jun Chen
KWKeld West
Keld West
GWGordon G. Wallace
Gordon G. Wallace

16 August 2013 in IEEE Sensors Journal
Verified
Journal Article
Closed access
EAEmran Md. Amin
Emran Md. Amin
SBShakil Bhuiyan
Shakil Bhuiyan
Nemai Chandra KarmakarNemai Chandra Karmakar
Nemai Chandra Karmakar
BWBjørn Winther-Jensen
Bjørn Winther-Jensen
A novel low-cost chipless radio frequency identification tag sensor is presented. The tag sensor provides identification data as well as monitors relative humidity (RH) of tagged objects. The tag sensor is made of passive microwave circuit that uses humidity sensitive polymer material for RH sensing. The aim of this paper is to investigate RF sensing properties of moisture absorbing polymer polyvinyl alcohol at microwave frequency. In addition, frequency shifting technique is used to encode data bits for high data capacity. The overall size of the proposed tag sensor is 15 mm × 6.8 mm and has 6 bit data capacity for ID generation and single bit for humidity sensing. Results presented here show ~ 607 MHz frequency deviation for 50% RH increase. The tag sensor has potential to be printed on flexible laminates such as plastic and paper for ultra-low cost item level tagging and ubiquitous sensing.

1 December 2009 in Journal of Power Sources
Verified
Journal Article
Closed access
MHM. Hilder
M. Hilder
BWB. Winther-Jensen
B. Winther-Jensen
NCN.B. Clark
N.B. Clark