The object of research is a riverbed in the area of a bridge crossing, which is subject to the action of high water during the passage of a flood. The selection of parameters and contours of the scheme of the river section was carried out using a mathematical model of the flow and deformation of the bed of the riverbed before and after the change of its shape. It was established that the assignment of parameters of the operational slot should be performed on the basis of the principle of creating natural analogs of riverbed shapes, riverbed and floodplain terraces, with the use of mathematical modeling. To reduce erosion in the area of bridge crossings, it is proposed to regulate the riverbed by constructing a canalized riverbed. Modeling according to this option showed that the erosion in the span of a road bridge decreased and did not exceed 1.5 m. In addition, it was established that a significant role in ensuring the stability of the river is played by the vegetation cover in floodplain areas. Using the method of mathematical modeling, it was established that the area near the convex bank with a width of 150 m is subject to the strongest erosion in the design of the supports. Siltation of the existing left-bank bottom basin is also observed. It is recommended to make a decision to carry out restorative cutting of riverbed alignment annually after receiving a flood forecast from the local hydrometeorological station. In the case of a high flood warning, work should be carried out to clear the sleeves on the approach to the construction of the bridge deck. It was established that the most stable shape of riverbeds is in the form of curvilinear incomplete meandering when the radii of curvature R and the width of the riverbed B satisfy the ratio R=(4...7) B at riverbed-forming flow rate. At the same time, radii of curvature R<3.5 B should not be allowed, as this leads to separation of the flow from the convex bank and excessive erosion of the concave bank Об’єктом досліджень є русло в зоні мостового переходу, яке зазнає дії високих вод при проходженні паводку. Виконано вибір параметрів та обрисів схеми прорізу річки за допомогою математичної моделі течії та деформації дна русла до та після зміни його форми. Встановлено, що призначення параметрів експлуатаційного прорізу має виконуватись на основі принципу створення природних аналогів руслових форм, русло та заплавні тераси, із застосуванням математичного моделювання. Для зменшення розмиву на ділянці мостових переходів запропоновано провести регулювання русла шляхом створення каналізованого русла. Моделювання за цим варіантом показало, що розмив в створі автомобільного моста зменшився і не перевищує 1.5 м. Крім цього встановлено, що значну роль у забезпеченні стійкості річища відіграє рослинний покрив на заплавних ділянках. Методом математичного моделювання встановлено, що найбільш сильному розмиву в проектному створі опор піддається ділянка біля опуклого берега шириною 150 м. Спостерігається також замулення існуючої лівобережної донної улоговини. Рішення щодо проведення відновного зрізання регулювання русла рекомендується проводити щорічно після отримання прогнозу про паводок від місцевої Гідрометеорологічної станції. У разі попередження про високий паводок слід провести роботи з розчищення рукавів на підході до створу мостового полотна. Встановлено, що найбільш стійку форму мають русла у вигляді криволінійного незавершеного меандрування, коли радіуси кривизни R і ширини русла B задовольняють співвідношенню R=(4 ... 7) B при руслоформуючих витратах. При цьому радіуси кривизни R<3,5 B не повинні допускатися, оскільки це призводить до відриву потоку від опуклого берега і надмірного розмиву увігнутого берега